Important Warning - Chicco NIGHTLIGHT AUTO-CLOSE SAFETY GATE Manual De Instrucciones

N
ightlight

IMPORTANT WARNING

WARNING: The opening between the side of the door and
the outer-most vertical members of the barrier shall be less
than 60 mm
WARNING: Before use, remove and dispose of all plastic bags
and packaging materials and keep them out of reach of new-
born babies and children.
IMPORTANT
READ AND FOL-
LOW THESE IN-
S T R U C T I O N S
C A R E F U L L Y
AND KEEP FOR
FUTURE REFER-
ENCE.
WARNINGS
• WARNING: Incorrect installation can be dangerous.
• WARNING: This safety barrier barrier must not be fitted
across windows.
• Only use this product as a staircase and door guard. This
safety barrier is for domestic use only.
• This safety barrier has been designed for children up to 24
months of age.
• WARNING: Children over 24 months of age could climb on
the guard and pose a risk of danger to their safety barrier.
• WARNING: Stop using the safety barrier barrier if the child
is capable of climbing it.
• WARNING: Periodically check that the guard is fitted and
fixed correctly.
• Check that the surfaces where you wish to fit the guard
are suitable for this purpose and that they are structurally
solid.
• WARNING: Do not use the safety barrier if any components
are damaged or missing.
• WARNING: Additional or replacement parts should only be
obtained from the manufacturer or distributor.
• WARNING: The safety gate must be fitted in such a way so
that it opens in the direction opposite to the stairs.
• WARNING: Never use without wall cups
• The safety barrier closes and locks in place automatically.
Check that the safety barrier is closed properly.
MAINTENANCE
Periodically check the condition of the anchoring surfaces,
cranks, shafts, wall caps and the correct operation of the lock-
ing device of the safety barrier guard.
The cleaning and maintenance of this product must be
carried out on a regular basis by the user. The cleaning
and maintenance must only be carried out by an adult.
• Clean the plastic parts with a soft damp cloth.
• If the highchair comes into contact with water, dry the
–
metal parts to prevent the formation of rust.
PACK CONTENT (DIAGRAM A)
1. Safety gate
2. Shaft (x 4)
3. Crank (x 4)
4. Wall cap (x 4)
5. Adhesive strips (x 4)
6. Screw (x 4)
7. Spacer for fitting the guard.
HOW TO ASSEMBLE THE PRODUCT
Screw the cranks to the end of the shafts, taking care to fit
them in the correct positions, as shown in diagram B.
Insert each shaft, with the crank correctly tightened into po-
sition, into each of the appropriate housings located on the
corners of the guard (diagram B).
HOW TO POSITION THE SAFETY BARRIER GUARD
Minimum width: 760 mm
Maximum width: 810 mm
The safety gate can be fitted with extensions to suit larger
openings.
WARNING: Fitting the guard in the incorrect position can be
dangerous for your child's safety barrier.
The guard must be fitted in such a way so that it opens in the
direction opposite to the staircase.
WARNING: If the safety gate is positioned at the top of the
stairs, it must not be fitted below the highest step. If the safety
gate is positioned at the bottom of the stairs, it must be fitted
in correspondence with the lowest step (diagram C). Check
that the surfaces on which the safety gate is fitted are suit-
able and solid.
Note: Fitting the safety gate to certain surfaces may require pur-
chasing appropriate fixing accessories (i.e.: inserts).
HOW TO FIT THE SAFETY BARRIER GUARD
WARNING: To ensure the correct operation of the auto-close
locking mechanism, the safety gate must be fitted in a perpen-
dicular position with respect to the floor' s surface, as shown in
diagram D.
HOW TO ASSEMBLE AND USE THE SAFETY GATE
Place the safety gate in a central position with respect to the
opening, as shown in diagram E. The safety gate must be per-
fectly perpendicular with respect to the floor surface. Adjust
the right and left cranks to the same degree, ensuring that the
safety gate is tightly fixed to the wall caps. Ensure that the latter
are firmly fitted to the anchoring surfaces. Mark the position of
the four wall caps on the anchoring surface, then remove the
safety gate. Depending on the type of anchoring surface, glue
12