Honeywell Energy Smart HZ-7200 Serie Guia De Inicio Rapido página 2

Calentador fresco al tacto
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Do not use it in the areas where gasoline, paint or
flammable liquids are used or stored.
16. Use this heater only as described in this manual. Any
other use not recommended by the manufacturer
may cause fire, electric shock, or injury to persons.
17. Avoid the use of an extension cord because the
extension cord may overheat and cause a risk of fire.
However, if you have to use an extension cord, the
cord shall be No. 14 AWG minimum size and rated
not less than 1875 watts.
18. Never tamper with this product or attempt to fix
it. Any tampering with, or modification of, this
product can result in serious injury, death, fire or risk
of electric shock. Do not open, no user serviceable
parts inside.
19. Do not remove product labels that contain warnings
or safety instruction.
20. The output of this heater may vary and its
temperature may become intense enough to burn
OPERATION
• Place the heater on a firm, level, open surface free from
obstructions and at least 3 feet (0.9 m) away from any
combustible materials.
• Never leave an operating unit unattended.
• Plug the heater into an electrical wall outlet.
• Touch the Power Button ( ) to turn the heater on.
The Power Indicator Light will illuminate. Fig. 1
• To save up to 35% in energy bills, turn the Energy
Smart™ Control Knob to your desired temperature.
There are four distinct settings of 65°F/18°C, 70°F/ 21°C,
75°F/23°C, and 80°F/26°C. The Energy Smart™ heater
will automatically select the appropriate power level to
best accommodate your Desired Temperature. As the air
temperature in the room approaches the set temp, the
heater will automatically lower the power consumption
and provide consistent warmth without wasting energy.
• The illuminated LED lights will indicate what the current
room temperature is.
NOTE: The LOW ( ) setting is designed to operate only if the temperature is below 55°F (12°C). If the room temperature is
above 55°F (12°C), the heater will remain OFF until the temperature drops below this level. If you want the heater to operate
when the room temperature is above 55°F (12°C), move the Control Knob to a higher setting.
• To override the Energy Smart™ feature and produce maximum heat, turn the knob fully clockwise
This will produce 1500W of heat at all times.
• To turn on the oscillation feature, press the ( ) button once. To turn it off, press the ( ) button once more. Please note,
the oscillation function will stop when the Energy Smart™ mode has reached the desired temperature and the heater is no
longer blowing warm air. It will start back up when the heater starts blowing warm air again.
2
exposed skin. Use of this heater is not recommended
for persons with reduced sensitivity to heat or an
inability to react to avoid burns.
21. Before cleaning, or storage, or when not in use, turn
the unit off and unplug from the electrical outlet.
22. Place the heater on a firm, level, open surface free
from obstructions and at least 3 feet (0.9 m) away
from any combustible materials. DO NOT use on an
unstable surface such as bedding or deep carpeting.
Be sure the heater is not in a position where it
may be tripped over by small children or pets. The
heater's rubber feet will hold it firmly in position.
Caution - If your home has aluminum wiring
23.
have a licensed electrician check your receptacle's
connections. When using any 1500 watt heater,
aluminum wire connections can cause a safety issue.
SAVE THESE INSTRUCTIONS
24.
Fig. 1
Energy Smart
Control Knob
Power
Button
Power Indicator Light
Oscillation
Button
to HIGH ( ).

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Energy smart hz-8000 serie

Tabla de contenido