Peavey PV 2015 D Manual De Instrucciones página 23

ARCHITECTURAL AND ENGINEERING SPECIFICATIONS
The powered loudspeaker system shall have a frequency response from 56 Hz to 18 kHz. The peak SPL with
inaudible distortion shall reach 127 dB with music as a source, when measured at a distance of 1M and driven
to full output capacity. The system shall utilize dual heavy-duty 15" Peavey
™
Peavey RX 14 titanium diaphragm compression driver tweeter on a patented asymmetrical Quadratic Throat
™
Waveguide constant directivity horn. The nominal radiation geometry shall be 100 degrees in the horizontal
plane and 50 degrees in the vertical plane. The vertical plane radiation geometry shall be asymmetrical, at +15,
-35 degrees.
The powered loudspeaker system shall have a medium impedance input connector consisting of one combo
female XLR and 1/4" RTS phone jack on the rear panel. Output connections on the rear panel shall consist of a
1/4" phone jack providing link-out, which provides a pre-level control signal for the use of linking multiple PV
2015D enclosures in a line. A level control will be located next to the input jack. Next to the level control, a Contour
Switch push button will provide some bass and treble lift when engaged for improved listening at low levels.
The system power amplifier shall have an unfiltered frequency response of 20 Hz to 20 kHz which deviates no
more than +0, -3 dB up to rated power, a damping factor greater than 200 @ 1 kHz into 4 Ohms, hum and noise
better than 90 dB below rated power, and typical THD and IMD of less than 0.5%. The amplifier shall be capable
of 400W continuous output into a 4 Ohm nominal load and shall incorporate DDT
The enclosure shall be constructed of MDF-type wood panels, and be covered in black carpet. A pair of metal
handles shall be provided on the sides. A black-coated perforated metal grille shall be provided for speaker
component protection. The cabinet shall incorporate 4 rubber feet for floor standing use.
The outside dimensions shall be 43.63" tall by 18.13" wide by 16.88" deep, and the weight shall be 83 lbs.
Power requirements shall be a dual voltage range of: 100 to 120VAC, and 220 to 240VAC, 50 - 60 Hz, with a
nominal power consumption of 370 watts. The voltage ranges shall be switch selectable on the rear panel. The
loudspeaker system shall be called a Peavey model PV 2015D.
PEAVEY PV 2015D - SPECIFICATIONS
Enclosure: Peavey PV 2015D
Frequency Range 1 meter on-axis, swept-sine in 1/2 Space
environment: -10 dB: 39 Hz to 21 kHz
Frequency Response 1 meter on-axis, swept-sine in 1/2 Space
environment: 58 Hz to 17 kHz (±3 dB )
Sensitivity: (1w/1m) 98 dB
Maximum Peak SPL: 127 dB
Transducer Compliment: Dual heavy-duty Pro 15 15" woofer with 2
3/8" voice coil & 50 oz. Magnet
RX 14 1.4" titanium diaphragm dynamic compression driver, loaded
™
on a Peavey exclusive 100° by 50° Quadratic Throat Waveguide.
Nominal Coverage Pattern: 100° horizontal X 50° vertical Axis of the
vertical main polar lobe is angled down 10°, resulting in the angular
pattern with respect to straight ahead being +15, -35°
Electro-Acoustic Crossover Frequency: 2.8 kHz
Input Connections: One combo female XLR/ 1/4" phone jack
providing balanced or unbalanced operation.
Enclosure Materials & Finish: Trapezoidal, black carpet covered
15mm MDF, black powder-coated full length perforated steel grille.
Mounting or Suspension: Four rubber feet for floor use.
NOTE: This unit is not designed for overhead suspension!
Dimensions (H x W x D):
Front: 43.63 in. x 18.13 in. x 16.88 in.
1108 mm x 461 mm x 429 mm
Rear: 43.63 in. x 15.38 in. x 16.88 in.
1108 mm x 391 mm x 429 mm
Sheffield model woofers, and a
®
™
Weight:
83 Lbs. (37.7 kg)
ELECTRONICS AND AMPLIFIER SPECIFICATIONS:
Power Amp Rating, Total Power Output: 800 watts peak available
power Continuous Power: 400 watts into 4 Ohms @ less than 1%
distortion
Electronic Input Impedance (Nominal): 2.7 k Ohms balanced (XLR or
1/4"), 1.35 k Ohms unbalanced 1/4".
Infrasonic Filter Protection: 24 dB/octave roll-off
Nominal Amplifier Frequency Response: +0, -3 dB from 20 Hz to 20 kHz
Hum and Noise: Greater than 90 dB below rated power
DDT Dynamic Range: Greater than 14 dB
THD and IM: Typically less than 0.5 %
Damping Factor: Greater than 200 @ 1000 Hz, 4 Ohms
Power Requirements of Peavey PV®2015D System: Nominal 370
Watts, Voltage and Frequency Ranges: 100-120 VAC, and 220 –
240VAC, at 50- 60 Hz
Fuse Type: International fuse classification T6.3AL . In the USA,
types GDC, GMC, 215, 218, and 477 cartridge-style 5 x 20 mm size
fuses with a 6.3 amp 250V rating can be used.
compression.