Troubleshooting - Franke FDW 613 E5P F Manual De Usuario

TROUBLESHOOTING

In case your dishwasher doesn't work properly, check if the problem can be solved by going through the following list.
For other errors or issues please contact authorized After-sales Service which contact details can be found in the warranty booklet.
The manufacturer ensures the availability of spare parts for at least 10 years after production date of this appliance.
PROBLEMS POSSIBLE CAUSES
Salt reservoir is empty. (After refill the salt
Salt
indicator may remain lit for several wash
indicator is lit
cycles).
Rinse aid dispenser is empty. (After refill the
Rinse aid
rinse aid indicator may remain lit for several
indicator is lit
wash cycles).
The appliance has not been plugged in
properly.
Power outage.
The dishwasher
won't start or
The dishwasher door is not closed.
does not respond
Cycle is interupted by door opening for
to commands.
more than 4 seconds.
It does not respond to commands.
The wash cycle has not finished yet.
The drain hose is bent.
The dishwasher
won't drain.
The sink drain pipe is blocked.
The filter is clogged up with food residues.
The dishes are rattling against each
The dishwasher
makes excessive
An excessive amount of foam has been
noise.
produced.
The crockery has not been arranged
properly.
The spray arms cannot rotate freely, being
hindered by the dishes.
The wash cycle is too gentle.
The dishes are
An excessive amount of foam has been
not clean.
produced.
The cap on the rinse aid compartment has
not been shut correctly.
The filter is soiled or clogged.
There is no salt.
No water in the water supply or the tap is
The dishwasher
closed.
does not fill the
water.
The inlet hose is bent.
All LEDs are
The sieve in the water inlet hose is clogged;
blinking rapidly
it is necessary to clean it
Drain hose positioned too low or siphoning
Dishwasher
into home sewage system.
finishes the cycle
prematurely.
Air in water supply.
SOLUTIONS
Refill reservoir with salt (for more information - see page 5).
Adjust water hardness - see table, page 5.
Refill dispenser with rinse aid (for more information - see page 5).
Insert the plug into the socket.
For safety reasons, dishwasher will not re-start automatically when power
returns. Open dishwasher door, press START/Pause button and close the door
within 4 seconds.
Vigorously push the door until you hear the "click".
Press START/Pause and close the door within 4 seconds.
Switch off the appliance by pressing the ON/OFF button, switch it back on after
approximately one minute and restart the program. If problem persists, unplug
the appliance for 1 minute, then plug it back in.
Wait until the wash cycle finishes.
Check that the drain hose is not bent (see INSTALATION INSTRUCTION).
Clean the sink drain pipe.
Clean the filter (see CLEANING THE FILTER ASSEMBLY).
Position the crockery correctly (see LOADING THE RACKS).
The detergent has not been measured out correctly or it is not suitable for
use in dishwashers (see FILLING THE DETERGENT DISPENSER). Restart the cur-
rent cycle by switching OFF the dishwasher, then switch it on again, select a
new program, press START/Pause and close the door within 4 seconds.
Please do not add any detergent.
Arrange the crockery correctly (see LOADING THE RACKS).
Arrange the crockery correctly (see LOADING THE RACKS).
Select an appropriate wash cycle (see PROGRAMS TABLE).
The detergent has not been measured out correctly or it is not suitable for use
in dishwashers (see FILLING THE DETERGENT DISPENSER).
Make sure the cap of the rinse aid dispenser is closed.
Clean the filter assembly (see CARE AND MAINTENANCE).
Fill the salt reservoir (see FILLING THE SALT RESERVOIR).
Make sure there is water in the water supply or the tap running.
Make sure the inlet hose is not bent (see INSTALLATION) reprogram the
dishwasher and reboot.
After having carried out the verification and cleaning, turn off and turn on the
dishwasher and restart a new program.
Check if end of drain hose is placed at correct height (see INSTALLATION).
Check for siphoning into home sewage system, install air admittance valve if
necessary.
Check water supply for leaks or other issues letting air inside.
EN
13