Weber Summit 89796 Guia Del Propietario página 6

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

6
TYPICAL BULK PROPANE GAS SUPPLY INSTALLATION
We recommend that this installation be done by a LICENSED professional.
General Specifications for Piping
Note - Contact your local municipality for building codes regulating outdoor gas grill
installations. In absence of Local Codes, you must conform to the latest edition of the
National Fuel Gas Code ANSI Z223.1/NFPA 54.
This grill is designed to operate at 11 inches of water column pressure. An LP in
line regulator may be necessary for this pressure.
CAUTION: If young children are in the area, a
locking valve should be considered.
Pipe compound should be used which is resistant to the action of liquid propane
gas when gas connections are made.
The gas connections must be firmly attached to rigid, permanent construction.
Note: The information provided in this manual is general for typical installations. We
cannot cover all possible installation ideas. We recommend, prior to installation, that you
contact your municipality for local building codes and your local fire department for
installation verification.
If you have any questions, contact Customer Service at 1-800-446-1071.
Table
Maximum Capacity of Metallic Pipe in Cubic Feet of Gas per Hour for Gas Pressures of 2 psi or Less and
6.2(a)
Nominal
Actual
Iron Pipe
ID:
Size
(Inches)
10
(Inches)
1/2
.622
131
3/4
.824
273
1
1.049
514
1 1/4
1.380
1,060
1/12
1.610
1,580
2
2.067
3,050
2 1/2
2.469
4,860
3
3.068
8,580
4
4.026
17,500
© 2007 National Fire Protection Association, Inc. and International Approval Services - U.S., Inc. All Rights Reserved.
GAS INSTRUCTIONS
a Pressure Drop of 0.3 Inch Water Column. (Based on a 0.60 Specific Gravity Gas)
20
30
40
50
90
72
62
55
188
151
129
114
353
284
243
215
726
583
499
442
1,090
873
747
662
2,090
1,680
1,440
1,280
3,340
2,680
2,290
2,030
5,900
4,740
4,050
3,590
12,000
9,660
8,270
7,330
GAS LINE PIPING
Refer to the piping chart at the bottom of previous page.
The corrugated gas line from the manifold is 58 inches (1,473.2 mm) long. Do not
extend the gas line.
We have provided the means to make an SAE 45° flare connection. Do not use
pipe sealant on this connection.
If the length of line required does not exceed 50 feet, use a 5/8" O.D. tube. One
size larger should be used for lengths greater than 50 feet. Refer to piping chart.
Gas piping may be copper tubing, type K or L; polyethylene plastic tube, with a
minimum wall thickness of .062 inch (1.57 mm); or standard weight (schedule 40)
steel or wrought iron pipe.
Copper tubing must be tin-lined if the gas contains more than 0.3 grams of
hydrogen sulfide per 100 cubic feet of gas.
Plastic tubing is suitable only for outdoor, underground use.
Gas piping in contact with earth, or any other material which may corrode the
piping, must be protected against corrosion in an approved manner.
Underground piping must have a minimum of 18" cover.
Length of Pipe (Feet)
60
70
80
90
50
46
42
40
104
95
89
83
195
179
167
157
400
368
343
322
600
552
514
482
1,160
1,060
989
928
1,840
1,690
1,580
1,480
3,260
3,000
2,790
2,610
6,640
6,110
5,680
5,330
100
125
150
175
38
33
30
28
79
70
63
58
148
131
119
109
304
269
244
224
455
403
366
336
877
777
704
648
1,400
1,240
1,120
1,030
2,470
2,190
1,980
1,820
5,040
4,460
4,050
3,720
WWW.WEBER.COM
200
26
54
102
209
313
602
960
1,700
3,460
®

Publicidad

Tabla de contenido
loading

Tabla de contenido