Before Calling For Service - Kenmore 796.8158 Manual De Uso Y Cuidado

Secador con vapor
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

BEFORE CALLING
FOR SERVICE
----IP_b
Possible CaUse
*CHECK VENT is
Exhaust system is too long or has too
blinklng
many turns/restrictions.
Partial blockage of the ductwork due
to lint buildup or other foreign object.
Install a shorter or straighter duct run. See the
Installation Instructions for details.
Ductwork should be checked/cleaned
immediately. Dryer can be used in this condition,
but drying times will be longer and energy
consumption will increase.
* This warning light does not indicate a dryer failure and is not covered by the dryer
warranty. Contact a duct cleaning service to set up an appointment
to have your
exhaust system cleaned and inspected.
Dryer will not turn on
Dryer does not heat
Greasy or dir|y spo_ on
doff_es
Excess sfaffc in clothes
after drying
Power cord is not properly plugged in.
House fuse is blown, circuit breaker
has tripped, or power outage has
occurred.
House fuse is blown, circuit breaker
has tripped, or power outage has
occurred.
Gas supply or service is turned off
(gas models only).
Clean and dirty clothes are being
dried together.
Clothes were not properly cleaned
or rinsed before being placed in the
dryer.
Fabric softener is not used or used
incorrectly.
Clothes dried too long (over dried).
Drying synthetics, permanent press,or
synthetic blends.
Heat settings, load size, or dampness
of clothing is not consistent.
Drying time is not
consis|enf
Make sure that the plug is securely plugged into a
grounded outlet matching the dryer's rating plate.
Reset circuit breaker or replace fuse. Do not
increase fuse capacity.
If the problem is a
circuit overload, have it corrected
by a qualined
electrician.
Reset circuit breaker or replace fuse. Do not
increase fuse capacity,
if the problem is a
circuit overload_ have it corrected
by a qualified
electrician.
NOTE: Due to the design of electric dryers, it is
possible for a circuit problem to allow an electric
dryer to run without heat.
Confirm that the house gas shutoff and the dryer
gas shutoff valves are both fully open. Even if gas
is not supplied to the dryer, it wiff run and no error
codes will display. Verify that other gas appliances
inthe home are working normally.
Only use your dryer to dry clean items.Soil from dirty
clothescan transfer to the dean clothesin the same
or later loads.
Stains on dried clothes could be stains that
weren't removed during the washing process.
Make sure that clothes are being completely
cleaned or rinsed according to the instructions for
your washer and detergent. Some difficult soils
may require pre-treating prior to washing.
Use a fabric softener or the STATIC SHIELD
option, if equipped, to reduce static electricity.
Be
sure to fotlow the fabric softener manufacturer's
instructions.
Overdrying
e load of laundry can cause a buildup
of static electricity. Adjust settings and use a
shorter drying time, or use AUTO DRY cycles.
These fabrics are naturally more prone to static
buildup. Try using fabric softener, or use DAMP
DRY and/or shorter TIMED DRY time settings.
Thedryingtimefor a load will vary depending on the type
of heat used(electric, natural g as,or LPgas),the sizeof the
load, thetype of fabrics,the_
of theclothes_ and
the cond_on of the exhaust d uct and lintfitter. E venan
unbalanced load inthewashercan causepoor spinning,
resulting in wetter clotheswhich will take Ior_jer to dry.
31

Publicidad

Capítulos

Tabla de contenido
loading

Este manual también es adecuado para:

796.9158

Tabla de contenido