General Operation; Radio Operation - Lenco CS-322 Manual De Instrucciones

1. POWER/MODE
2. 8┃
3. DISP/0
4. AMS
5. VOL/SEL/ ENT
6. LCD Display
7.
REMOTE SENSOR
8. (Release Button)
9. OPEN
10. Auxiliary input
11. 6/DIR+
12. 5/DIR-

GENERAL OPERATION

1. Switching on/off the unit
Press any button to turn on the unit. Long press "POWER" button to turn the unit off.
2. Remove the panel
Press button(8) to fold down and Remove the panel.
3. Sound adjusting
Press SEL button (5) shortly to select the desired adjustment mode. The adjustment mode will change in the
following order: VOL---BASS---TREBLE---BALANCE---FADER---LOUD---DSP OFF---DX---STEREO.
By rotating the audio knob (5) clockwise or counter-clockwise, it is possible to adjust the sound setting.
4. LOUDNESS on/off
In above menu. Keeping pressing SEL to enter LOUD setting. Then rotating VOL to turn it on/off.
5. SELECT EQ
In above menu. Keeping pressing SEL to enter DSP OFF setting. Then rotating VOL to select desired EQ function
as below: DSP OFF---CLASSIC---POP---ROCK
6. LOCAL/DISTANCE
In above menu. Keeping pressing SEL to enter DX setting. Then rotating VOL to select DX/LOC mode. In LOC
mode. During scanning. to reduce the sensitive of searcher and only receive the local stronger signals.
7. STEREO/MONO
In above menu. Keeping pressing SEL to enter STEREO setting. Then rotating VOL to select STEREO/MONO
mode. In STEREO mode. In stereo mode, when stereo broadcasting station is received, the "OO" icon will appear
upon the display.
8. LIQUID CRYSTAL DISPLAY
Exhibit current frequency and activated functions on the display.
9. AUXILIARY INPUT
The unit can be connected to a portable audio player through the AUX IN jack (10) on the front panel. After finishing
the connection, you can press MOD button (1) on the front panel to switch the mode to AUX IN mode.
10. RESET FUNCTION
RESET button (25) must be activated with either a ballpoint pen or thin metal object. The RESET button has to be
activated for the following reasons:
- Initial installation of the unit when all wiring is completed.
- All the function buttons do not operate.
- Error symbol on the display.
Note: if press RESET button, All the memory will be lost!
OPERATION
13. 4/RDM
14 3/RPT
15. 2/INT
16. 1 /
17. 9/ ┃ ┃ ┃ ┃
18. BAND /PTY/7
19. TA
20. MUTE/AF
21. USB
22. SD CARD SLOT
23. Reset Button
5

RADIO OPERATION

1. SWITCHING TO RADIO MODE
Keep pressing MOD button (1) shortly till the radio mode appears in the display.
2. SELECTING THE FREQUENCY BAND
In radio mode, press BANDbutton (18) shortly to select the desired band.
The reception band will change in the following order: FM1--FM2--FM3--AM1(MW1)--AM2(MW2).
3. SELECTING STATION
▎ button (17) or 8┃ ┃ ┃ ┃
Press 9 button (2) shortly to to activate automatic seek function. It will search the station
automatically. Press for several seconds until "MANUAL" appears on the display, the manual tuning mode is
▎ or 8┃ ┃ ┃ ┃
selected. Every time 9 is pressed the frequency will change with 0,05 MHz.
4. AUTOMATIC MEMORY STORING & PROGRAM SCANNING
- Automatic memory storing
Press AMS button (4) for 2 seconds, the radio searches the signal strength until one cycle search is finished.
And then the 6 strongest stations are stored into the corresponding preset number button.
- Program scanning
Press AMS button (4) shortly to preview all the preset stations.
5. MANUAL STORING A STATION
To receive a station and press one of the preset button(11/12/13/14/15/16) for several seconds, current station is
stored into the number button.
6. ANS (Announcement Name Station) OPERATION
- Setting AF mode
Long press AF button (20) to switch off or on AF mode.
Whenever AF is switch on, symbol "AF" appears on the display.
Program name is displayed on receiving a ANS station.
"AF" starts blinking if the broadcasting signal getting worse. And when the signal is too bad due a frequency
change. AF will automatically switch to the new frequency.
- Regional Program Operation
Press DISP/0 button (3) for several seconds to switch on or off region mode.
Some broadcasting stations change their program from normal broadcasting to regional broadcasting for a
certain time period. When region is on, the current listening program remains unchanged. When region is off, it
allows the reception moves to the regional station.
- Using PTY to Select Program
PTY button (20) 1 time.then press preset button(12/13/14/15/16/17). You can select the program type as below:
1# button: NEWS/AFFAIR/INFORM
2# button: EDUCATIO/DRAMA/SPORT
3# button: VARIED/CULTURE/SCIENCE
4# button: ECONOMY/CHILD PR/WEATHER
5# button: PHONE IN/SOCIAL/RELIGION
6# button: TRAVEL/LEISURE/DOCUMENT
PTY button (20) 2 time.then press preset button(12/13/14/15/16/17). You can select the program type as below:
1# button: ROCK MUS/POP MUSI
2# button: LIGHT MU/EASY MUS
3# button: OTHER MU/CLASSICS
4# button: COUNTRY/JAZZ MUS
5# button: NATIONAL/OLDIES
6# button: FOLK MUS
- Listening to Traffic Announcement
OPERATION
6