Beninca RR.4WBV Manual De Instrucciones página 8

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 20
- Four output, independent and freely congurable channels
- Rolling code radio receiver - 433.92MHz frequency
- Programming through built-in LCD display
- Programming through ADVANTAGE programmer and corresponding software for PC Windows (optional).
- Setting for GSM module (optional) to check outputs with any GSM telephone.
- Standard memory for 512 transmitters. It can be replaced with MEM2048 module for 2048 transmitters
- Versions with 230VAC, 115VAC or 24VAC/CC power supply are available.
- Input for 12VDC emergency battery, with automatic charge.
Input, No.
1-2
Power supply
3-4
Channel 1
5-6
Channel 2
7-8
Channel 3
9-10
Channel 4
11-12
Antenna
13-14
Battery
GSM
Connector GSM
ADV
Connector,
ADVANTAGE
The U2 memory can contain 512 rolling-code, 433.92MHz, transmitters maximum. If necessary, it can be
replaced with item MEM2048 which can contain up to 2048 different codes.
The programming of the various functions of the control unit is carried out by using the LCD display in the
receiver and presetting the desired values in the programming menus described hereunder.
1 - Press the <PG> key, the display shows the rst Parameters Menu "PAR".
2 - By using the keys <+> or <->, select the desired Menu (PAR>>LOG>>RADIO>>....).
3 - Press the <PG> key, the display shows the rst function available on the Menu.
4 - By using the keys <+> or <->, select the function to be modied.
5 - Press the <PG> key, the currently preset value for the selected function is displayed.
8
RR.4WBV Programmable, Four-channel Radio Receiver
INPUT/OUTPUT FUNCTIONS
Function
Input, 230Vac 50Hz (1-Phase/2-Neutral) in the 230V version
Input, 115Vac 60Hz (1-Phase/2-Neutral) in the 115V version
Input, 24 Vac/dc (1+ /2 -) in the 24V version
Output, channel 1. 230 Vac max 5A.
Normally Open (N.O.) Contact,
switchable in Normally Closed (N.C.) through jumper 1.
Output, channel 2. 230 Vac max 5A.
N.O. Contact, switchable in N.C. through jumper 2.
Output, channel 3. 230 Vac max 5A.
N.O. Contact switchable in N.C. through jumper 3.
Output, channel 4. 230 Vac max 5A.
N.O. Contact, switchable in N.C. through jumper 4.
Antenna connection of the built-in radio module
(11-screen/12-signal).
Input for emergency battery, 12Vdc (13:- / 14:+).
It allows the operation of the receiver in case of power failure of the mains,
During the mains operation the battery is recharged.
Recharge time, about 15 hours for a battery 12V/1,2Ah.
Consumption: 1A with GSM module, 0.2A without GSM module.
Insertable connector for GSM module (optional), to control the receiver
through GSM mobile.
For further information, please refer to instructions supplied with the GSM
module.
Note: to use these functions a SIM-DATA card must be provided, as well
as the relevant telephone contract with a telephone operator in the instal-
lation area.
Input for ADVANTAGE PRX connector.
The receiver memory can be managed through the ADVANTAGE software
and the relevant programmer.
For further information, please refer to ADVANTAGE instructions
SPECIFICATIONS
Description
Note:
PROGRAMMING

Publicidad

Tabla de contenido
loading

Tabla de contenido