• Keep the fastening belts out of reach of
children.
• Only use the mattress provided with
the product or replacement mattresses
approved by Artsana.
• Do not add other mattresses or other
materials between the structure and the
supplied mattress or between the supplied
mattress and the child (e.g., to raise the
child).
• Use the crib in "Co-Sleeping configuration
(fastened to the bed)" only with beds of the
size indicted in the reference figure at the
beginning of the manual.
• Do not leave anything inside the product
that might reduce its depth.
• To prevent it becoming trapped, do not
place the cot close to walls or obstacles.
• Do not leave any small objects inside the
product that might be swallowed.
• Do not make adjustments to the product
when the child is in it.
• Do not use the rocking function if the child
is unattended in the crib. Block the crib
in locked position whenever the child is
unattended.
• Do not use the rocking function when
the crib is in "Co-Sleeping configuration
(fastened to the bed). "
• Do not move the product when the child
is inside.
• Do not use the product for more than one
child at a time.
• The product must be kept away from
electrical cables and cords: do not position
close to windows where cords, curtains or
similar could pose a suffocation or choking
hazard. To avoid all risks of strangulation,
never give children objects with cords or
strings attached, or leave them within their
reach.
• Prolonged exposure to direct sunlight can
cause the colours of the fabric to fade.
After a prolonged exposure of the product
to high temperatures, wait a few minutes
prior to putting your child in it.
• All components must be duly engaged; also
make sure that there are no open zippers
or buttons, as body parts or clothing of the
child make get caught (stings, necklaces,
pacifier chains, etc.), causing a hazard of
strangling.
• Keep the product out of reach of children
when it is not in use.
COMPONENTS
A. Leg rest with wheels
A1. Height adjustment button
A2. Rocking slide
A3. Height indicator
A4. Foot rotation release button
A5. Articulated feet
A6. Wheels with brakes
A7. Slide deactivation button
A8. Cross slots
B. Upper structure
B1. Fixed structure
B2. Mobile structure
B3. Foot hook
B4. Side tilting handle
B5. Fabric attachment buttons
C. Central support structure
C1. Fastening pin
C2. Fabric lining attachment buttons
C3. Grey fastening buckles
D. Fastening straps
D1. Red fastening buckles
E. Fabric lining
E1. Strap with clip
E2. Pocket
E3. Fabric removal zipper
E4. Net windows
E5. Rigid tabs for fastening the fabric lining to the upper
structure
F. Mattress with removable lining
G. Bottom bar
H. Bag
ASSEMBLY OF THE CRIB:
1. Hold foot support "A" and make the outer bar slide up until
you hear it CLICK into the first position (fig.1). Repeat this step
for the other foot support.
2. Insert the lower bar "G" in the relevant slots inside the foot
supports "A" (fig.2) until you hear the metal pin lock into place.
3. Fasten the upper structure "B" to the two feet as shown in
figure 3. The CLICK of the pin means that the structure is
correctly fastened.
WARNING: Make sure the grey buckles are facing the same
side as the articulated feet (fig.4).
4. Mount the upper structure "B" and fit the fabric "E" on the
feet "A" making the bar of the foot slide first inside the lateral
pocket of the fabric (fig.5). Repeat the step on both sides.
WARNING: The structure must be oriented so that the
side with the handle "B4" is facing the same direction as the
articulated feet "A5. "
5. Then fasten the upper structure to the feet by inserting the
11
relevant plastic support as shown in figure 6. Push down until