Faber NEW CRISTAL CRIS36SS300 Instrucciones De Instalacion, Informacion De Uso Y Cuidado página 9

7
ELECTRICAL INSTALLATION
WITH CONNECTION CABLE
GROUNDING INSTRUCTIONS This appliance must be grounded.
In the event of an electrical short circuit, grounding reduces the risk
of electric shock by providing an escape wire for the electric current.
This appliance is equipped with a cord having a grounding wire with
a grounding plug. The plug must be plugged into an outlet that is
properly installed and grounded.
WARNING - Improper grounding can result in a risk of electric shock.
Consult a qualified electrician if the grounding instructions are not
completely understood, or if doubt exists as to whether the appliance
is properly grounded.
Do not use an extension cord. If the power supply cord is too short,
have a qualified electrician install an outlet near the appliance.
ELECTRICAL INSTALLATION WITH OPTIONAL
WIRING BOX
For Permanent wiring Installation-Use only with Listed
rangehood Wiring Box kit
sku # WIREBOX, manufactured by Faber.
FRONT TRIM OPTIONS
The New Cristal comes with a stainless front strip installed.
FRONT TRIM OPTIONS
Optional black and white strips are available as accessories
for purchase. To change the front strip, remove the three phil-
The New Cristal comes with a stainless front strip installed.
lips screws located behind the strip (FIGURE 8). If necessary,
Optional black and white strips are available as accessories
the front strip can be adjusted by loosening the three phillips
for purchase. To change the front strip, remove the three phil-
lips screws located behind the strip (FIGURE 8). If necessary,
screws and sliding the strip up or down. Tighten screws when
the front strip can be adjusted by loosening the three phillips
you have the strip properly placed.
screws and sliding the strip up or down. Tighten screws when
you have the strip properly placed.
For a custom front strip, a local cabinet shop can make a strip
to match your cabinets. The front strip dimensions are given
For a custom front strip, a local cabinet shop can make a strip
to match your cabinets. The front strip dimensions are given
in FIGURE 9 .
in FIGURE 9 .
Visor
Visor
Front
Strip
Front
Strip
9
Three Screws
Three Screws
FIGURE 8
FIGURE 8
1
Direct Connect Wiring Box
Accessory sku # WIREBOX
(purchased separately)
The New Cristal comes with a stainless front strip installed.
Optional black and white strips are available as accessories
for purchase. To change the front strip, remove the three phil-
lips screws located behind the strip (FIGURE 8). If necessary,
the front strip can be adjusted by loosening the three phillips
screws and sliding the strip up or down. Tighten screws when
you have the strip properly placed.
For a custom front strip, a local cabinet shop can make a strip
to match your cabinets. The front strip dimensions are given
in FIGURE 9 .
Front
Strip
Rangehood Control Panel
All controls are located on the right side of the rangehood.
Light On/O Switch
TheOn/O switch for the halogen light is located behind the
front trim. Moving the switch to the 1 Position turns the light
On. Moving the switch to the 0 position turns the light o .
15/32"
Blower Speed Switch
FRONT TRIM OPTIONS
Visor
Three Screws
FIGURE 8
FIGURE 10
29 or 35
7/8" 7/8"
FIGURE 9
USE AND CARE INFORMATION
USE AND CARE INFORMATION
Rangehood Control Panel
All controls are located on the right side of the
Light On/O Switch
TheOn/O switch for the halogen light is locat
2x
front trim. Moving the switch to the 1 Position
Max. 33 "
7/16
B
Ran
All c
Ligh
The
FIGURE 10
fron
On.
1
15/32"
Blow
3/4"
B in
blow
on L
on M
blow
the
Aut
As l
and
and
For
Star