DeWalt DCF6201 Manual Del Usuario página 15

Setting Magazine Screw Length (Fig. C)
This magazine is designed for 25– 57 mm screw lengths. Failure
to set the correct screw length can cause screws to not be
driven accurately which can result in the failure to advance to
the next screw or screws not being driven properly. The shoe
has marked specific slots for each of the most common
12
screws, however this attachment can still drive any size screw
between 25– 57 mm. To accommodate for less common screws
adjust to the next longest slot.

CAUTION: Do not adjust while a screw strip is in
the magazine.
1. Slide screw length adjustment tab
2. Holding the screw length adjustment tab in place, adjust
the shoe 5 to the desired length.
3. Release the screw length adjustment tab. Make sure that the
locking pin has fully returned and is in the correct position.
Inserting Collated Screw Strips (Fig. D)
NOTICE: Use only screw strips that are suitable to this
magazine. Only insert screw strips when the screwdriver
power is off and the trigger is locked.
Proper use of collated strips will reduce the risk of injury, reduce
jams and prevents screws from damaging workpiece. For best
performance use new, undamaged strips free of debris.
1. Take a collated strip, holding the plastic portion, and feed
from the bottom of the screw guide
of the advancing mechanism
2. Continue feeding the strip until the first screw is one slot
below the driver bit.
Setting Screw Depth (Fig. A)
Turn fine depth adjustment 3
behind the tool) to make the screw head stop raised from
the workpiece.
Turn fine depth adjustment
3
head stop deeper into the workpiece.
There is a window to show where in the adjustment range
the tool is. When the slider is furthest from the tool the screw
head will stop in the most raised position. When the slider is
closest to the screwdriver tool the screw head will stop in its
deepest position.
Driving Screws (Fig. A)
1. Before driving screws, ensure screwdriver drive direction is
switched to forward position.
nOtE: Always hold the screwdriver perpendicular
to workpiece.
2. With the magazine installed on the screwdriver, position
shoe 5 on workpiece in location where screw is to
be driven.
3. Switch the screwdriver on by holding the trigger in the on
position. Continue to hold trigger or engage the trigger
lock-on.
4. Apply pressure against workpiece. This will advance screw
into alignment with screwdriver bit.
2 to the left.
1 and into the bottom
4 .
anti-clockwise (as viewed from
clockwise to make the screw
5. Continue to apply consistent pressure until screw is driven
in completely and screwdriver clutches disengage.
6. Lift screwdriver from workpiece.
The magazine is designed to drive screws completely into
workpiece only. Once screwdriver is lifted, adjustments to screw
must be made by first removing magazine.
Rotating the Collated Attachment
This attachment has the ability to rotate without being taken
off the drywall screwdriver. To rotate, grip the top portion with
one hand, while holding the drywall screwdriver with the other
then rotate. An audible "click" indicates the magazine is in each
of the available positions.
MAINTENANCE
Your D WALT power tool has been designed to operate
e
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. Be sure the
trigger switch is in the OFF position. An accidental start-up
can cause injury.
Lubrication
Your power tool requires no additional lubrication.
Cleaning

WARNING: Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing this procedure.

WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into a liquid.
For best performance clean magazine by:
1. Remove advancing mechanism from collated magazine (see
Removing and Installing the advancing Mechanism
instructions).
2. Remove shoe from advancing mechanism.
3. Remove return spring from magazine.
4. Submerge parts in soapy water for 10 minutes.
5. Remove and thoroughly rinse parts.
6. Allow parts to air dry.
7. Reassemble and continue use.
EngLIsh
13