Silverline 10.8V Manual Del Usuario página 7

652640
Fitting a driver bit
WARNING: DO NOT fit any attachment with a maximum speed lower than the no load speed of
the machine.
1. Pull the Collar (2) of the Hex Bit Holder (1) forward and insert the bit
2. Release the Collar
3. Pull on the bit to check that it is securely fitted. If the bit is not secure, repeat steps 1 and 2
Note: Make sure screwdriver bits used are hardened and suitable for use with an impact driver.
Operation
Direction control
WARNING: The rotational direction of the bit holder cannot be changed while the impact drill is
running. DO NOT attempt to change the rotational direction while the impact driver is running; this
may cause permanent damage to the tool.
• Use the Forward/Reverse Switch (5) to change the direction of the bit rotation
• For anti-clockwise rotation, push the switch to the right
• For clockwise rotation, push the switch to the left
Note: When the Forward/Reverse Switch is in the central position, the impact driver is locked and
cannot be switched 'ON' . Use this setting as a safety feature to prevent the impact driver from being
switched 'ON' accidentally.
Switching ON & OFF
WARNING: ALWAYS wear adequate personal protective equipment when setting up and
operating this machine.
1. To start the impact driver, squeeze the Trigger Switch (6)
2. The built-in LED Work Light (10) will illuminate when the Trigger Switch is squeezed
Note: If the Trigger Switch cannot be pressed down, check that the Forward/Reverse Switch (5) is not
set to its middle position, which locks the device (see 'Direction control')
3. The speed of the impact driver is controlled by the movement of the trigger: the more the Trigger
Switch is pressed down, the faster the impact driver will run
4. Release the Trigger Switch to stop the tool
WARNING: If the power tool gets excessively hot in use, stop using the tool immediately and
allow to cool before continuing work. The cooling period can be reduced by operating the impact
driver at maximum speed with no load. Always make sure the Motor Vents (3) are not blocked and
do not allow dust to enter the body of the tool through the Motor Vents; dust, especially metallic
dust, may damage or destroy the tool.
Accessories
• A full range of accessories including various types of screwdriver bits is available from your
Silverline stockist
• Spare parts can be obtained from toolsparesonline.com
Maintenance
WARNING: Before carrying out any maintenance/cleaning of the Battery Charger (11), ALWAYS
disconnect from the mains power supply. Remove the battery before carrying out any maintenance/
cleaning of the impact driver.
Note: Both the impact driver and the charger contain no user-serviceable parts. If the device does
not perform as outlined in this manual, return it to an authorised Silverline service centre for repair.
General inspection
• Regularly check that all the fixing screws are tight
• Inspect the supply cord of the tool, prior to each use, for damage or wear. Repairs should be
carried out by an authorised Silverline service centre. This advice also applies to extension cords
used with this tool
Cleaning
• Keep your tool clean at all times. Dirt and dust will cause internal parts to wear quickly, and
shorten the machine's service life. Clean the body of your machine with a soft brush, or dry cloth.
If available, use clean, dry, compressed air to blow through the ventilation holes
• Clean the tool casing with a soft damp cloth using a mild detergent. Do not use alcohol, petrol
or strong cleaning agents
• Never use caustic agents to clean plastic parts
Lubrication
• Slightly lubricate all moving parts at regular intervals with a suitable spray lubricant
Contact
For technical or repair service advice, please contact the helpline on (+44) 1935 382 222
Web: silverlinetools.com/en-GB/Support
Address:
Powerbox
Boundary Way
Lufton Trading Estate
Yeovil, Somerset
BA22 8HZ, United Kingdom
Storage
• Store this tool carefully in a secure, dry place out of the reach of children
Disposal
Always adhere to national regulations when disposing of power tools that are no longer functional
and are not viable for repair.
• Do not dispose of power tools, or other waste electrical and electronic equipment (WEEE), with
household waste
• Contact your local waste disposal authority for information on the correct way to dispose of
power tools
• Li-ion batteries should not be disposed of with household waste. If you do not know of a Li-ion
battery recycling centre in your area, contact your local authority or original dealer for advice on
disposal of Li-ion batteries
silverlinetools.com
10.8V Impact Driver
7