Waste Management; General Description - GYS FLASH 10.36/48 PL Traducción De Las Instrucciones Originales

Translation of the original instructions

Waste management:

• This product should be disposed of at an appropriate
recycling facility. Do not throw away in a household bin.

GENERAL DESCRIPTION

GYSflash 10.36/48 PL is ideal for charging most lead-acid (Gel, AGM, Liquid,...) and lithium batteries of the Lithium Iron Phosphate
(LFP / LiFePO4) and «standard» lithium-ion types such as Nickel Manganese Cobalt (NMC), Lithium nickel cobalt aluminium oxide
(NCA), Lithium Cobalt Oxide (LCO), Lithium Polymer (Li-Po), Lithium Manganese Cobalt Oxide (MCO), etc.
This charger is perfectly suited for charging :
- 36 V lead batteries (18 cells in series)
- 48 V lead batteries (24 cells in series)
- 36 V Lithium batteries (12 cells in series)
- 48 V LFP batteries (15 cells in series) - 48 V LFP batteries (16 cells in series)
- «Standard» Lithium-ion batteries 48 V (13 cells in series)
- «Standard» Lithium-ion batteries 48 V (14 cells in series)
CALIBRATION CABLE
Procedure for the calibration of the charging leads in order for the charger to compensate any voltage drop due to the length or
condition of the cables. It is strongly recommended to perform this procedure each time the cables are modified or changed.
1. Before undertaking the procedure, make sure that the charger is disconnected from the mains socket.
2. Short-circuit the ends of the charging leads.
3. Press buttons
4. Plug in the mains plug while holding down the two buttons until the indicator light
Results :
- Indicator is on : the calibration was successful.
- Indicator is on: the calibration failed, disconnect the mains plug and restart the procedure.
5. Unplug the mains plug until the charger switches off.
START UP
1. Connect the charger to the battery.
2. Plug the charger to the mains (single phase 220-240Vac 50-60Hz).
3. Select the charging voltages (or the number of cells in your battery) by pressing button
nology press button
4. During the charge, the device indicates charge progress. When indicator
Once indicator is steady, the battery is fully charged.
5. The charge can be interrupted at any time by unplugging the mains plug or pressing the
6. After the charge, disconnect the charger from the mains, then disconnect the clamps from the battery.
CHARGE MODES
• Description of charging modes and currents :
10
GYSFLASH 10.36/48 PL
The Gysflash 10.36/48 PL is equipped with a function that automatically adjusts the output voltage
according to the ambient air temperature when charging the lead battery. This adjustment ensures a highly
precise charge, relative to the temperature of the room.
and simultaneously.
. After roughly five seconds, the charge starts automatically.
Lead CHARGE mode (43.8 V/10 A max) :
Mode for charging 36 V lead-acid batteries from 20 Ah to 230 Ah. Automatic seven step charge cycle.
Lithium Iron Phosphate Charging Mode (43.2 V/10 A max) :
Mode for charging 36 V LiFePO4 batteries from 10 Ah to 230 Ah. Eight-step automatic charging cycle.
Standard Lithium-ion charging mode (41.5 V/10 A max) :
Mode for charging 36 V Li-ion standard batteries from 10 Ah to 230 Ah. Eight-step automatic charging
cycle.
Lead CHARGE mode (58.4 V/8 A max)
Mode for charging 48V Lead-acid batteries from 15Ah to 160 Ah. Automatic seven step charge cycle.
or lights up.
,to select the battery tech-
flashes, the battery is ready to start the engine.
button.
EN