Descargar Imprimir esta página
Eaton HALO WP1150LPC Instrucciones
Eaton HALO WP1150LPC Instrucciones

Eaton HALO WP1150LPC Instrucciones

Publicidad

Enlaces rápidos

WP1150LPC
WP1150LPCH
WP1135LPC
ENGLISH
ITEMS REQUIRED
(Purchase separately)
• Phillips screwdriver
• Flat head screwdriver
• Weatherproof silicone caulk
IMPORTANT SAFETY INSTRUCTIONS
When using product, basic precautions should always be followed, including the following:
• Heed all warnings, including below warnings AND those included on product.
• Save these instructions and warnings.
• For outdoor use only.
• cULus LISTED for wet location.
• Disassembling your fixture will void the warranty.
• Your fixture is prewired and preassembled for easy installation.
WARNING
• Read and follow these instructions.
• Risk of fire/electric shock. If not qualified, consult an electrician.
• Disconnect power at fuse or circuit breaker before installing or servicing.
CAUTION
• Connect fixture to a 120 volt, 60 Hz power source. Any other connection voids
the warranty.
• Fixture should be installed by persons with experience in household wiring or by a
qualified electrician. The electrical system, and the method of electrically connecting
the fixture to it, must be in accordance with the National Electrical Code and local
building codes.
• Fixture designed for wall or eave mount to a junction box only. Mount fixture to a
grounded, recessed-mounted standard junction box marked for use in wet locations.
• Do not mount below 5 feet.
• This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may cause
undesired operation.
WARNING: FCC Regulations state that any unauthorized changes or
modifications to this equipment not expressly approved by the manufacturer
could void the user's authorization to operate this equipment.
SAVE THESE INSTRUCTIONS.
Questions?/ Des questions?/ ¿Preguntas? 1-800-334-6871 ConsumerProducts@eaton.com
PACKAGING CONTENTS/ CONTENU DE L'EMBALLAGE/CONTENIDO DEL PAQUETE
A. Fixture housing
Alojamiento del portalámparas
Boîtier de l'appareil d'éclairage
D. Lens screw (installed in fixture)
F. (2) #6 and (2) #8 screws
(2) Tornillos #6 y (2) tornillos #8
(2) #6 et (2) vis #8
Instruction Manual / Manuel d'instructions/ Instrucciones
B. Lens (installed on fixture)
Lente (instalado en el artefacto)
Lentille (installée sur l'appareil)
Tornillo del lente (instalado en el artefacto)
Vis de lentille (installée dans l'appareil)
INSTALLING YOUR FIXTURE
1. Turn power OFF at main breaker that runs to the junction box where fixture will be installed.
2. Attach adjustable mounting bracket (C) to junction box on wall using two of the mounting
plate screws provided (F). Either the #6 or #8 screws (F) provided will fit most standard
junction boxes. Position the bracket (C) so that the mounting studs (C) for the fixture are
horizontal. Tighten the rotation screws (C) on the bracket.
3. Wire the fixture as described in "Wiring your fixture".
4. Remove Lens (B) by removing Lens screw (D), and tilting Lens away from the fixture at the
bottom.
5. Position the fixture so that the bracket screws pass through the backplate of the fixture
housing (A). Tighten the housing (A) to the mounting bracket (C) with the knobs (C)
provided. Make sure your fixture is straight. Mounting bracket (C) does swivel so you can
adjust to get fixture straight. Reinstall Lens (B) using Lens screw (D).
6. Add silicone caulk around fixture to help maintain a weather resistant seal.
7. Turn power back ON.
WIRING YOUR FIXTURE
1. Turn the power OFF at main fuse/breaker box.
2. Connect the black fixture wire to the black supply wire (hot). Secure with a wire connector (E).
3. Connect the white fixture wire to the white supply wire (neutral). Secure with a wire
connector (E).
4. Connect the bare ground wire on the mounting bracket (C) to an appropriate supply
ground or grounded junction box. Secure with a wire connector (E).
NOTE: Be careful to connect the wires correctly. Make sure no bare strands of wire are
sticking out of the wire connectors (E).
MANUAL OPERATION
NOTE: You may choose to override the photo control.
This will allow you to control the fixture from a wall
switch without the dusk-to-dawn feature.
1. Snap the photo control cover (G) over the photo
control on the face of the fixture (Fig. 1).
1
C. Adjustable mounting bracket, knobs and screws
Soporte de montaje ajustable, perillas y tornillos
Support de montage réglable, boutons et vis
E (3) Wire connectors
(3) Conectores de cable
(3) Serre-fils
G. Photo control cover (optional)
Cubierta del control de foto celda (opcional)
Couvercle de l'interrupteur photo-électrique
(facultatif)
G
Fig. 1

Publicidad

loading

Resumen de contenidos para Eaton HALO WP1150LPC

  • Página 1 Instruction Manual / Manuel d’instructions/ Instrucciones Questions?/ Des questions?/ ¿Preguntas? 1-800-334-6871 ConsumerProducts@eaton.com PACKAGING CONTENTS/ CONTENU DE L’EMBALLAGE/CONTENIDO DEL PAQUETE B. Lens (installed on fixture) A. Fixture housing C. Adjustable mounting bracket, knobs and screws Lente (instalado en el artefacto) Alojamiento del portalámparas Soporte de montaje ajustable, perillas y tornillos Boîtier de l’appareil d’éclairage...
  • Página 2 WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. los tornillos (C) giratorio sobre el brazo de montaje. Eaton warrants to customers that, for a period of five years from the date of purchase, Eaton 3. Conecte el portalámparas tal y como se describe en “Cableado del portalámparas.”...
  • Página 3 La reproducción de este documento sin la aprobación previa por escrito de Eaton está estrictamente prohibida. Para solicitar ayuda, llame al 1-800-334-6871 o envíe un correo electrónico a ConsumerProducts@eaton.com...
  • Página 4 PARTICULIER. CÂBLAGE DU DISPOSITIF Eaton garantit à ses clients, pendant une période de cinq ans à compter de la date d’achat, que ses produits Eaton sont exempts de tout défaut de matériaux et de fabrication. En vertu 1. Coupez le courant au disjoncteur principal.

Este manual también es adecuado para:

Halo wp1150lpchHalo wp1135lpc