Circular Saw Safety - GMC MS018 Manual De Usuario

WARNING: Do not use the tool if the on/off switch does not turn it on and off.
The switch must be repaired before the tool is used.
21. Have your tool repaired by a qualified person - This electric tool
complies with the relevant safety rules. Repairs should only be carried out
by qualified persons, otherwise this may result in considerable danger to
the user.
WARNING: When servicing use only identical replacement parts.
WARNING: If the power cable is damaged it must be replaced by the
manufacturer or an authorised service centre.
22. Power tool mains plugs must match the mains socket - Never modify
GB
the plug in any way. Do not use adapter plugs with earthed (grounded)
power tools. Unmodified plugs and matching sockets will reduce risk of
electric shock.
23. If operating a power tool outside or in a damp location, use a
residual current device (RCD) - Use of an RCD reduces the risk of
electric shock.
NOTE: The term "residual current device (RCD)" may be replaced by the
term "ground fault circuit interrupter (GFCI)" or "earth leakage circuit
breaker (ELCB)".
WARNING: When used in Australia or New Zealand, it is recommended that
this tool is ALWAYS supplied via Residual Current Device (RCD) with a rated
residual current of 30mA or less.
Polarized Plugs (for North America only. To reduce the risk of electric shock,
this equipment has a polarised plug (one blade is wider than the other). This
plug will fit in a polarised outlet only one way. If the plug does not fit fully in the
outlet, reverse the plug. If it still does not fit, contact a qualified electrician to
install the proper outlet. Do not change the plug in any way.
WARNING: USE PROPER EXTENSION CORD.
USE PROPER EXTENSION CORD. Make sure your extension cord is in good
condition. When using an extension cord, be sure to use one heavy enough to
carry the current your product will draw. An undersized cord will cause a drop in
line voltage resulting in loss of power and overheating.
An 18AWG cord is suitable for the total length up to 25', 16AWG for 50', 14AWG
for 100'. If in doubt, use the next heavier gauge (the smaller the gauge number,
the heavier the cord).

Circular Saw Safety

WARNING: Before connecting a tool to a power source (mains switch power
point receptacle, outlet, etc.) be sure that the voltage supply is the same as that
specified on the nameplate of the tool. A power source with a voltage greater
than that specified for the tool can result in serious injury to the user, and
damage to the tool. If in doubt, do not plug in the tool. Using a power source
with a voltage less than the nameplate rating is harmful to the motor.
WARNING: Guards supplied with saws should always be fitted and used where
possible. Always re-fit guards that are meant to be permanently attached in use
after maintenance or replacing blades. Inspect guards before use to make sure
they are not damaged and are secure.
• Do not allow anyone under the age of 18 years to operate this saw
• When operating the saw, use safety equipment including safety goggles or
shield, ear protection, dust mask and protective clothing including
safety gloves
• Hand-held power tools may produce vibration. Vibration can cause
disease. Gloves may help to maintain good blood circulation in the fingers.
Hand-held tools should not be used for long periods without a break
• Always use recommended blades with correct size and shape of arbor
holes e.g. diamond or round. Blades that do not match the mounting
hardware of the saw will run eccentrically, causing loss of control
• Whenever possible, use a vacuum dust extraction system to control
dust/waste
• Power tools must always be held by the insulated gripping surfaces when
performing an operation, ensuring protection if the cutting tool makes
contact with its own cord or hidden wiring. Contact with a 'live' wire will
make exposed metal parts of the power tool 'live' and shock the operator if
the insulated gripping surfaces are not used
• Ensure hands are kept away from the cutting area and blade. Keep one
hand on the auxiliary handle or motor housing. If both hands are holding
the tool they cannot be cut by the blade
• Do not attempt to cut material thicker than detailed in the Specifications
section of this manual
• Adjust the cutting depth to the thickness of the workpiece i.e. less than a
full tooth of the blade should be visible below the workpiece
• Ensure that work is correctly supported. Large panels may sag under their
own weight and bind the saw blade. Supports must be placed under the
panel on both sides, close to the line of cut and near the edge of the panel
• Ensure all supports and power cables are completely clear of the
cutting path
• Always secure the workpiece to a stable platform, ensuring body exposure
is minimised, avoiding blade binding, or loss of control
• For accuracy of cut, and to avoid blade binding, always use a rip fence or
straight edge guide
• Never hold a workpiece in your hand or across your legs whilst cutting
• Always stand at an angle to the tool when operating
• Be aware that the blade will project from the underside of the workpiece
• Do not reach beneath the workpiece where the guard cannot protect you
from the blade
• Note the direction of rotation of the motor and the blade
• Inspect the workpiece and remove all nails and other embedded objects
prior to starting work
8