Cooper Lighting MS600 Manual De Instrucciones

MS600 (Bronze)
MS600W (White)
ENGLISH
ITEMS REQUIRED
(Purchase separately)
• Phillips screwdriver
• Flathead screwdriver
• Outdoor weatherproof silicone caulking
• (2) 150 watt (MAX) PAR 38 floodlight bulbs
NOTE: This fixture was designed to work with up to 150 watt maximum PAR halogen flood
bulbs. For improved energy efficiency, lower wattage PAR halogen flood bulbs may be used.
Compact Fluorescent (CFL) bulbs contain electronics which may interfere with the motion
sensing function of your fixture and are not recommended. To meet ENERGY STAR
requirements, maximum lamp wattage can not exceed 250 watts.
HOW IT WORKS
Your motion activated floodlight senses heat images from
objects such as people, large animals and automobile engines.
When motion is detected, the lights will automatically turn
on. Once motion has stopped, the lights will turn off after a
preselected time delay. Your motion activated floodlight may
also be used as a standard floodlight.
WARNINGS AND CAUTIONS
• Follow all instructions.
• For outdoor use only.
• cULus LISTED for wet locations.
• Connect fixture to a 120 volt, 60 Hz power source. Any other connection voids the warranty.
• Fixture should be mounted to a grounded recessed mounted standard junction box marked
for use in wet locations.
• Suitable for wall mount or eave mount only. NOT suitable for ground mount installation.
• Keep away from flammable objects. Do not position fixture within two inches
of any combustible materials.
• Bulb gets HOT quickly!
• The bulb and fixture get extremely hot during use. Disconnect power
and allow fixture to cool before changing bulb or handling fixture.
• Fixture should be installed by persons with experience in household wiring or by a qualified
electrician. The electrical system, and the method of electrically connecting the fixture to it,
must be in accordance with the National Electrical Code and local building codes.
• Always replace bulb with the same wattage or lower wattage than marked. Installing a
bulb of a higher wattage could create a fire hazard. Use of a higher wattage bulb will void
the warranty. (Maximum 150 watt halogen bulb.) To meet ENERGY STAR
maximum lamp wattage cannot exceed 250 watts.
• Do not use this apparatus near water.
• Clean only with a dry cloth.
• Do not block any ventilation openings. Install in accordance with the manufacturer's
instructions.
Questions? / ¿Preguntas ? 1-800-334-6871 ConsumerProducts@cooperlighting.com
PACKAGING CONTENTS / CONTENIDO DEL PAQUETE
A. Light fixture B. Coverplate gasket
Artefacto de luz
E. Center bolt
Perno central
180 degrees
® requirements,
C. (2) Lampholder gaskets
Junta de la placa (2) Juntas obturadoras
de cubierta del receptáculo
F. (3) Wire nuts
(3) Tuercas para alambre
• Do not install near any heat sources such as radiators, heat registers, stoves or other
apparatus (including amplifiers) that produce heat.
• Only use attachments/accessories specified by the manufacturer.
• Disassembly of your fixture will void the warranty.
• Your fixture is prewired and preassembled for easy installation.
• MINIMUM 90° C SUPPLY CONDUCTORS.
• This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation. Under Part 15 of the FCC Rules, any changes or modifications to the motion
detector described in this instruction sheet that are not expressly approved by Cooper
Lighting, LLC could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
®
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
Up to
equipment generates, uses and can radiate radio frequency energy and if not installed
40 feet
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
- R eorient or relocate the receiving antenna.
- I ncrease the separation between the equipment and receiver.
- C onnect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
- C onsult the dealer or an experienced radio/TV technician for help.
WARNING: FCC Regulations state that any unauthorized changes or modifications
to this equipment not expressly approved by the manufacturer could void the user's
authorization to operate this equipment.
SAVE THESE INSTRUCTIONS.
FOR BEST RESULTS
• Install the motion sensor/transmitter 8-12 feet above
the ground. (Motion sensor is less sensitive above 12
feet.) For installation above 12 feet, remove lens and
reinsert with "NEAR" on top of lens frame (Fig. 1).
• Locate motion sensor so motion moves across
detection zone (Fig. 2).
• Locate sensor away from heat producing sources to
prevent false triggering. Also be very careful not to
include objects such as windows, white walls and
water in the detection zone.
• Locate sensor away from moving objects such as
trees, large shrubs and street traffic.
• Do not install more than one motion activated
floodlight on one wall switch.
1
Instruction Manual / Instrucciones
D. (4) Mounting bracket screws
(use the size that fits your junction box)
(4) Tornillos del soporte de montaje
(utilice el tamaño que mejor se
adecue a su caja de conexión)
G. Universal mounting bracket
Soporte para montaje universal
Fig. 1
Fig. 2
NEAR