Cooper Lighting MS600 Manual De Instrucciones página 2

MOUNTING AND WIRING YOUR FIXTURE
WARNING: Deviation from the assembly instructions
may result in the risk of fire or electric shock.
1. Turn off power at the main fuse/breaker box.
2. Attach universal mounting bracket (G) to recessed
junction box. Junction box must be at least 1-1/2
inch in depth for proper installation (Fig. 3).
3. Thread fixture wires through coverplate
gasket (B) (Fig. 4).
4. If the supply wires coming from you house are
solid, you can use the Quick-connect™ wire
system to attach your Cooper Lighting, LLC light
fixture. Quick connectors can only be used with
solid wire supply leads. Simply insert the black
supply wire from your house into the quick connec-
tor with black wire coming from the fixture. Repeat
for house white wire, matching to the connector
with the white wire. Push both wires firmly into
holes to insure that they are seated properly and
securely (Fig. 5). It's that easy! Proceed to Step 6.
5. If the supply wires coming from your house are
stranded, remove the quick connectors from the
end of the light fixture wires by turning them
repeatedly from left to right while pulling.
Repeat until they are both removed.
NOTE: Quick connectors can only be used with
solid wire supply leads. Do not attempt to use with
other electrical fixtures! These connectors are
designed to withstand the temperature and voltage
requirements of this Cooper Lighting, LLC product
only. Once the connectors have been removed, connect
black wire to house black wire and connect white wire
to house white wire using the wire nuts (F) provided.
6. Connect the ground wire coming from your house
to the ground wire on mounting bracket (G) using
the wire nuts (F) provided.
7. Attach fixture to mounting bracket (G) using center
bolt (E) provided.
8. Apply silicone caulk around the edges of coverplate
and any open screw holes for a watertight seal.
9. Insert gaskets (C) into lampholders and screw
bulbs into each lampholder (Fig. 6). (Do not
overtighten bulbs.)
10. Turn on power at mainfuse/breaker box.
OPERATING YOUR FIXTURE
1. Remove the lens by gently squeezing the lens
frame sides and then pull out straight (Fig. 7).
2. Slide the "TIME" Switch to the "T" position.
3. Slide the "SENS" Switch to the "M" position.
4. Reinstall lens. For installation above 12 feet, insert
lens with "NEAR" on top of the lens frame. For
installation below 12 feet, insert lens with "FAR"
on top of the lens frame.
5. Aim bulbs at least 1/2 inch away from sensor and
slightly downward so water will not fill lampholders.
(Use lampholders to adjust lamp direction, not the
bulbs. The bulbs may break if they are used to
adjust the lampholders!)
6. Turn on the power to the fixture. Lights will turn on
for approximately 40 seconds.
7. Walk across the detection zone at the farthest
distance you wish your detector to detect motion.
(Lights will turn off approximately 4 seconds after
all motion has stopped.)
8. If you need more range, remove the lens and set
the "SENS" switch to the "H" position. If even more
range is required, rotate and reinsert so "FAR" is on
top of lens frame. To reduce range, remove the lens
and set the "SENS" switch to the "L" position. To
reduce the range even more, rotate and reinsert the
lens so "NEAR" is on top of the lens frame.
9. Move the "TIME" slide switch to "4" for 4 minute
mode or "12" for 12 minute mode to control
how long your lights stay on at night after motion
is detected.
Fig. 3
1-1/2 inch 1-1/2 inch
Round Octagonal
Fig. 4
B
A
Wall mount
B
A
Eave mount
Fig. 5
Solid
fixture
wire
Prewired quick
Solid house
connector
supply wire
Fig. 6
C
A
C
Fig. 7
2
ENERGY STAR ®
ENERGY STAR ®
Environmental Protection Agency & U.S.
Department of Energy.
Visit www.energystar.gov to learn more.
To meet ENERGY STAR ® requirements, the photo sensor control knob must be in the
"Auto" mode to prevent operation during full daylight. Maximum lamp wattage cannot
exceed 250 watts.
SELECTING YOUR DESIRED FEATURE
Mode of
Operation
"Auto" Setting
(motion activated)
Lights should turn ON with
motion only at night and
should turn OFF after
4-12 minutes of no motion.
Dusk-to-Dawn Setting
(activated only at night)
Lights should stay ON from
dusk to dawn and then reset
to "Auto" setting at
the next dawn.
Standard Floodlight Setting
Lights should stay ON
continuously both day and night
(must be reset manually).
Test Setting
Lights should turn ON with
motion both day and night.
Lights should turn OFF
after 4 seconds.
Return to "Auto"
(motion activated) Setting
from any of
the above settings.
TROUBLESHOOTING
Problem Cause / Solution
Outdoor Lights No power to the fixture.
Do Not Come • Check if circuit breaker tripped.
On With Motion • Confirm wall switch is ON.
At Night Bulb is faulty.
• Replace bulb.
Surrounding external ambient light is too bright. (If so, the unit may
think it is daytime.)
• Cover the photocell with tape.
TURN OFF POWER BEFORE CONTINUING
Wiring to the unit is loose.
• Check wiring, and reconnect if necessary using wire
nuts (F) provided.
Outdoor Lights There is motion in the detection zone.
• Make sure the sensor is not picking up moving objects such as
Come On For No
trees, traffic, etc.
Apparent Reason
TEST FOR YOURSELF.
At Night
• Cover the sensor lens with cardboard to prevent sensor from
detecting motion. If the light stays off, something in the detection
zone is triggering the sensor.
• If this is the case, reduce the sensitivity.
* If the light stays on with the sensor lens covered, contact
customer service.
Lights Stay On At There is motion in the detection zone.
Night And Do • Make sure the sensor is not picking up moving objects such as
trees, traffic, etc.
Not Turn Off
• Reduce the sensitivity.
Unit is in override mode (if there is no motion).
• Turn the light switch to the OFF position for 90 seconds, and then
turn back to the ON postion. Wait 40 seconds.
* If the lights continue to stay on, contact customer service.
is sponsored by the U.S.
MODE Knob How to Set
Adjustment Power Switch
AUTO 4 MIN Keep the power
or to the fixture ON.
AUTO 12 MIN
AUTO 4 MIN Turn the power
or OFF-ON-OFF-ON
AUTO 12 MIN within 3 seconds.
TEST Turn the power
OFF-ON-OFF-ON
within 3 seconds.
TEST Keep the power
to the fixture ON.
AUTO 4 MIN Turn the power OFF
or for at least 90 seconds
AUTO 12 MIN and then back ON.