Tabla De Contenido; Safety Information - Home Decorators Collection 51560 Guía De Uso Y Cuidado

Table of Contents
Table of Contents ................................................................ 2
Safety Information ............................................................... 2
Warranty ............................................................................... 3
Pre-Installation .................................................................... 3
Installation ............................................................................ 6

Safety Information

READ AND SAVE THESE INSTRUCTIONS
1. To reduce the risk of electric shock, ensure the electricity has been turned
off at the circuit breaker or fuse box before you begin.
2. All wiring must be in accordance with the National Electrical Code ANSI/
NFPA 70 and local electrical codes. Electrical installation should be
performed by a qualified licensed electrician.
The outlet box and support structure must be securely mounted and capable
3.
of reliably supporting 35 lbs. (15.9 kg). Use only UL Listed outlet boxes
marked "Acceptable for Fan Support of 35 lbs. (15.9 kg) or less."
4. The fan must be mounted with a minimum of 7 ft (2.1 m) clearance from the
trailing edge of the blades to the floor.
Do not place objects in the path of the blades.
5.
To avoid personal injury or damage to the fan and other items, use caution
6.
when working around or cleaning the fan.
7. Electrical diagrams are for reference only. Light kits that are not packed
with the fan must be UL-listed and marked suitable for use with the model
fan you are installing. Switches must be UL General Use Switches. Refer
to the instructions packaged with the light kits and switches for proper
assembly.
After making electrical connections, spliced conductors should be turned
8.
upward and pushed carefully up into the outlet box. The wires should be
spread apart with the grounded conductor and the equipment-grounding
conductor on one side of the outlet box.
9. All setscrews must be checked and retightened where necessary
before installation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help.
CAUTION:
Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including interference that may cause undesired operation.
Assembly .............................................................................. 7
Operation ........................................................................... 15
Care and Cleaning ............................................................. 17
Troubleshooting ................................................................. 17
WARNING: To reduce the risk of personal injury, do
not bend the blade brackets (also referred to as
flanges) during assembly or after installation. Do
not insert objects in the path of the blades.
WARNING: Remove the rubber motor stops on the
bottom of the fan before installing the blades or
testing the motor.
WARNING: To reduce the risk of fire or electric
shock, do not use this fan with any solid-state
speed control device.
WARNING: To reduce the risk of fire, electric shock
or personal injury, mount to outlet box marked
"Acceptable for fan support of 35 lbs. (15.9 Kg) or
less," and use screws provided with the outlet box.
WARNING: To avoid possible electrical shock, turn
the electricity off at the main fuse box before
wiring. If you feel you do not have enough electrical
wiring knowledge or experience, contact a licensed
electrician.
WARNING: Electrical diagrams are for reference
only. Optional use of any light kit shall be UL-listed
and marked suitable for use with this fan.
WARNING: To reduce the risk of fire or electric
shock, this fan should only be used with fan speed
control part no. RH786NR, manufactured by Rhine
Electronic Co.,LTD.
CAUTION: Changes or modifications not expressly
approved by the party responsible for compliance
could void the user's authority to operate the
equipment.
2