General Safety Practices; General Safety Rules; Operation Fundamentals Practices - Skymsen MPL Manual De Instrucciones

Con un destornillador , saque los tornillos que fijan la tapa trasera inferior y retírela ,
para tener acceso a las poleas . Usando una llave de tuerca ( 9/16" ) No. 02 (Fig. 05)
afloje los tornillos No.01 (Fig. 05 ) girándolos en sentido anti-horario .
En seguida con el auxilio de una palanca de madera No.03 (Fig. 05) , empuje el motor
en el sentido que provoque una mayor tensión de las Correas No. 05 (Foto 05) ,
después apriete los tornillos No.01 (Foto 05) .
Figura - 05
03
5.2.1 Ajuste del Cojinete Superior No.03 (Fig. 06):
El propósito de este ajuste es centralizar la hoja en el volante y evitar que la misma
salte afuera de el.
Para ajustar el cojinete superior siga las instrucciones abajo. con la maquina
desconectada de la red eléctrica .
Afloje la hoja No.06 (Fig. – 01) girando el manipulo No.01 (Fig. 01) en el sentido
anti-horario.
Retire la tapa trasera superior removiendo los tornillos con un destornillador.
Afloje las tres tuercas No. 01 (Fig. 06) usando una llave de tuerca de 10mm.
Usando un destornillador gire el tornillo superior No.02 (Fig – 06) ¼ de giro en
el sentido anti-horario si la lamina estuviera desplazada para adelante ó gire el tornillo
superior No.02 (Fig – 06) ¼ de giro en el sentido horario si la lamina estuviera
desplazada para tras.
Apriete las tres tuercas No.01 (Fig. 06) previamente aflojadas.
Calibre la tensión de la hoja como explicado en Pre-Operación , ítem 2.2 .Gire el volante
con las manos para averiguar si la hoja esta centralizada en el volante. Si ella no está
centralizada, continúe girando el volante hasta que la hoja se centralice .
Figura - 06
27
01
02
04 05
01
02

4.General Safety Practices

If any item from the GENERAL SAFETY NOTIONS section is not applicable to
of the machine as well as the person in charge of maintenance. The machine has to
be delivered to the operator in perfect conditions of use by the Distributor to the user.
The user shall operate the machine only after being well acquainted with the safety
procedures described in the present manual. READ THIS MANUAL WITH
ATTENTION.
4.1 Basic Operation Practices
4.1.1 Dangerous parts
parts when touched may cause severe electrical shocks or even be fatal.
Never touch commands such as buttons, switches and knobs with wet hands , wet clothes and/or
shoes. By not following these instructions operator could be exposed to severe electrical shocks or
even to a fatal situation.
4.1.2 Warnings
sure the Switch is easy to be reached when necessary. Before any kind of maintenance, physically
remove plug from the socket.
floor is clean and dry.
the command is the correct one. Check this manual for further details if necessary.
be given for each operation step. Every step of the operation shall be taken only if the sign has been
made and responded.
03
4.1.3 Advices
of the machine.
IMPORTANT
your product, please disregard it.
The following safety instructions are addressed to both the operator
Some parts of the electric devices are connected to high voltage points. These
The operator has to be well familiar with the position of ON/OFF Switch to make
Provide space for a comfortable operation thus avoiding accidents.
Water or oil spilled on the floor will turn it slippery and dangerous. Make sure the
Before giving any manual command (switch, buttons, turn keys or lever) be sure
Never use a manual command (switch, buttons, lever) unadvisedly.
If any work is to be made by two or more persons, coordination signs will have to
In case of power shortage, immediately turn the machine OFF.
Use recommended or equivalent lubricants, oils or greases.
Avoid mechanical shocks as they may cause failures or malfunction.
Avoid penetration of water, dirt or dust into mechanical or electrical components
08