Fellowes LX Serie Manual De Instrucciones página 2

LX201/LX211
A.
B.
C.
D.
E.
CAPABILITIES
Will shred: Paper, credit cards, staples and paper clips
Will not shred: Adhesive labels, continuous form paper,
transparencies, newspaper, cardboard, CD/DVDs, laminates,
file folders, X-rays or plastic other than noted above
* A4 (70g), paper at 220V-240V, 50/60 Hz, 2.5 Amps (LX201), 3.0 Amps (LX211), 3.8 Amps (LX221); heavier paper, humidity or other than rated voltage may
reduce capacity. Maximum recommended daily usage rates: 1000 sheets per day, 25 credit cards. Fellowes SafeSense
operated in home and office environments ranging between 50 – 80 degrees Fahrenheit (10 – 26 degrees Celsius) and 40 – 80% relative humidity.
WARNING! IMPORTANT SAFETY INSTRUCTIONS – Read before using!
• Operation, maintenance, and service requirements
are covered in the instruction manual. Read the entire
instruction manual before operating shredders.
• Keep away from children and pets. Keep hands away
from paper entry. Always set to off or unplug when
not in use.
• Keep foreign objects – gloves, jewelry, clothing, hair,
etc. – away from shredder openings. If object enters
top opening, switch to Reverse (
object.
15
• DO NOT use aerosol products, petroleum based or
aerosol lubricants on or near shredder. DO NOT USE
"CANNED AIR" OR "AIR DUSTERS" ON SHREDDER.
15
Vapors from propellants and petroleum based
lubricants may combust causing serious injury.
• Do not use if damaged or defective. Do not
disassemble shredder. Do not place near or over heat
source or water.
BASIC SHREDDING OPERATION
LX201
Continuous operation. Up to 10-minutes maximum.
NOTE: Shredder runs briefly after each pass to clear entry.
Continuous operation beyond 10-minutes will trigger
15-minute cool down period.
LX211
Continuous operation. Up to 20-minutes maximum.
NOTE: Shredder runs briefly after each pass to clear entry.
Continuous operation beyond 20-minutes will trigger
15-minute cool down period.
LX221
Continuous operation. Up to 20-minutes maximum.
NOTE: Shredder runs briefly after each pass to clear entry.
Continuous operation beyond 20-minutes will trigger
15-minute cool down period.
2
LX221
F.
A.
B.
G.
C.
D.
E.
) to back out
F.
A. SafeSense
G.
B. Paper entry
C. See safety instructions
D. Pullout bin
E. Casters
F. Disconnect power switch
1. OFF
2. ON
G. Control Panel and LEDs
Paper shred size: Micro-Cut, 2mm x 12mm
Maximum Sheets per pass:
LX201 - 12*, LX211 - 15*, LX221 - 20*
Maximum Paper entry width: 230mm
• This shredder has a Disconnect Power Switch
(F) that must be in the ON ( ) position to operate
shredder. In case of emergency, move switch to
OFF (O) position. This action will stop shredder
immediately.
• Avoid touching exposed cutting blades under
shredder head.
• Shredder must be plugged into a properly
grounded wall outlet or socket of the voltage
and amperage designated on the label. The
grounded outlet or socket must be installed near
the equipment and easily accessible. Energy
converters, transformers, or extension cords should
not be used with this product.
• FIRE HAZARD – Do NOT shred greeting cards with
sound chips or batteries.
• For indoor use only.
• Unplug shredder before cleaning or servicing.
PAPER OR CARD
1
Plug in and put disconnect power
switch in ON (I) position
2
Align paper/card to center of paper
entry. Feed straight into paper entry
and release.
ENGLISH
Technology
®
shredders are designed to be
®