Betec Aquarius Plus 006TD Manual Del Usuario página 4

AquariusPlus_Anleitung 29.11.2004
GB
Description of functions and parts
Thank you for purchasing our Water Dispenser. To achieve the best performance of the
product, you are recommended reading through this operation manual carefully before
using the product and keep this manual in good condition.
Introduction of features:
This product is advanced in functional design and cosmetic design, which include below
features:
1. Unique hot water tank with stainless steel thermal tube that could heat water to 92°C.
With its re-boiling function, it can heat the water up to 95°C, which will satisfy different
need, such as making tea, coffee and instant noodle, etc. It is good for use at home,
office and hotel, etc.
2. 3 in 1 faucet – one spout for hot water, cold water and room temperature water. Hot
and cold water can be obtained with simple touch of respective push buttons on the
control panel while traditional press bar structure is used for room temperature water.
3. 2 large circular tanks can be dismantled for cleaning purpose.
4. Designed to serve with replaceable filter to enhance purity of water.
5. The cooling function acquires the advanced thermo-electric (Peltier) system, which does
not generate loud noise as traditional compressor system does.
6. Versatile top cover, which allows to hold 2 – 5 Gallon large water bottles or 1.5 – 2L
PET-Bottled water by using the adaptor provided.
Structure Illustration & Parts Name:
Part No. 4001
1 PET bottle adaptor
2 Primary Water Tank (opaque)
3 Secondary Water Tank (transparent)
4 Room Temperature Water Press Bar
5 3 in 1 Faucet
6 Water Tray
7 Grip (on 2 sides)
8 Ventilation opening
Operation Instructions:
1. Place the water dispenser on flat surface and keep it approx. 15 cm from the wall to
allow good ventilation (Illustration A).
2. Sanitize the unit when using it for the first time or after long period storage. One disin-
fection tablet is provided with the new unit. Dissolve the disinfection tablet with approx.
5 gallon of water and fill it in the unit through the primary tank. Let the mixture water in
the unit for approx. 20 minutes before draining it. Pls add distilled water while draining
the mixture water until it becomes odorless (Illustration B – G).
3. Set the cooling-function switch and the heating-function switch (on the back of the unit)
at the "OFF" position first, then insert the power cord to the power socket. Press the
hot-water button on the control panel until water flows out from the faucet, it is then
okay to turn on the heating-function and cooling function
4. Please turn off the power if the unit is not in use for a long time. Disconnect the power
cord from the unit and drain the remaining water (see Dismantle and Clean) before stor-
age. When reviving to use the unit, please ensure that all parts are properly re-assem-
bled with good sealing condition.
5. Please refer to the Trouble Shooting for common problems. Do not disassemble the
water dispenser by yourself for its electrical part. Contact the authorized service facility
for repair when in necessity.
6. Do not start or stop the machine by inserting or pulling off of the power plug.
7. Turn off the cooling-function for 4 hours if ice is found to block the out-flow of water.
Illustration (1)
9:24 Uhr Seite 4
Aquarius Plus Water Dispenser
9 Cooling-function Switch
10 Power Socket
11 Heating-function Switch
12 Hot Water Button & Indicator
13 Re-boiling Button & Indicator
14 Cold Water Button & Indicator
15 Power Indicator
Screwing/Unscrewing Lever
Press-Board
Important
When the unit is firstly used or after periodical cleaning, please make sure that the hot
tank is filled with water before you turn on the heating switch (at the back of the unit). You
can detect whether or not the hot water tank is filled with water by pressing the "Hot" but-
ton on the control panel. Once the unit is connected to power, the power light on the con-
trol panel will be on and at the same time the "Hot" and "Cold" buttons will function to
release water when these buttons are pressed. At this stage, the water will only be at
room temperature. After you see water coming out from the faucet, you can start using
the heating and cooling functions by turning on the switches at the back of the unit.
This water dispenser is featured with a manually re-setting thermostat as safety device to
prevent hazard that may be caused by heating the hot water tank improperly when it is
empty. The thermostat will function to cut the power when the temperature inside the
empty hot tank gets to the alarming pre-set degree. You are required to press the re-set
button on the bottom of the unit to revive the heating function. The re-set button is cov-
ered with a label and you may remove the label to action.
Remarks:
1. There may be a few degrees difference in temperature for both hot and cold water.
2. The re-boiling function will not heat the water up to 100°C.
Specification for Switches and Push-buttons:
1. Turn on the heating-function switch and the red indicator will be lighted to indicate heat-
ing I in progress. When the indicator turns to yellow, it represents state of keeping
warm (Illustration H).
2. Turn on the cooling-function switch and the green indicator will be lighted to indicate
cooling in progress. When the indicator turns to yellow, it represents state of keeping
cool (Illustration I).
3. When the unit is in the mode of heating or keeping warm, the "Re-boiling" indicator and
the hot water indicator will all be lighted in red when the "Re-Boiling" function is used.
After water is heated to approx. 97°C, the buzzer will sound 3 times and heating will
stop to keep warm. The "Re-boiling" indicator and the hot water indicator will turn to
yellow. When the "Re-Boiling" in progress, you may press the "Re-boiling" switch once
again to return to keep-warm mode (Illustration J).
4. After the power is connected and the power indicator is on, you can press the hot water
button or cold water button to get water no matter the heating function switch and the
cooling function switch is turned on or off. While you press either cold or hot water
button, cold or hot water run out, and when you release the button it will stop.
5. The buzzer will sound one time on pressing the effective buttons. Otherwise, it will
sound for 10 times if there are faults with the function(s).
Technical Data:
Model 006TD Electric Safety Class
Voltage 220 - 240V Cooling Capacity
Rated Power 475W Heating Capacity
Heating Power 400W Ambient Temperature for operation
Cooling Power 75W
8. Please follow
the instructions
as shown in
illustration (2),
when you use
tap water.
4
I
≤ 15°C 1L/h
≥ 90°C 1L/h
10 - 32°C
Illustration (2)