Maintenance Measures; Troubleshooting - Betec Aquarius Plus 006TD Manual Del Usuario

AquariusPlus_Anleitung 29.11.2004
Attention:
To avoid electric shock, do not insert the
power plug with wet hand.
To avoid over loading, connect to
independent power outlet.

Maintenance Measures:

1. Disconnect the power cord and wait for approx. 2 hours to let hot water cool down so as
to avoid electric shock and scald.
2. Dismantle and Clean:
2. Firstly take off the bottle and the opaque cover. Secondly, screw off the nut at the inner
bottom of the transparent tank with the lever provided and push up the transparent tank
by inserting the 2 press-boards provided. Then, take out the insulation blocks from both
cold water tank and hot water tank; and pour out the remaining water carefully. Thirdly,
after cleaning the hot-water tank and the cold-water tank with clean water, you may re-
assemble the unit in the reverse procedures – place the insulation blocks in the hot
water tank and cold water tank – press the transparent tank back into the main body
properly (this procedure will require to apply with some strength) – make sure the 2 sil-
icon sealing gaskets on the bottom are not missed – screw the nut back in place with
the lever – make sure the nut is screwed tight, otherwise, it may lead to water leakage.
(Illustration K – V).
Never splash water onto the unit directly.
Do not drop or impact the unit.
9:24 Uhr Seite 5
Never change the plug of the power cord or,
extend its length so as to avoid over-heat or
fire. Please purchase/replace the damaged
power cord through dealer or the authorized
service facility.
Do not allow children to use the water dis-
penser without supervision or play with it to
avoid injury or scald.
Do not wipe the unit with detergent, organic
liquid or insecticide etc
Clean the unit with lightly moistened cloth
and let it dry naturally.
Place the water dispenser at dry, cool and
ventilated position. Do not place it close to
the valuable furniture or other household
appliances so as to avoid any possible dam-
age to them due to water spilling when fit-
ting the water bottle into the unit.
Trouble Shooting:
Check the listed items before returning the unit for repair.
Possible Causes
Problems
No water coming 1. Empty water tank(s)
out from the faucet 2. Heating tank or
cooling tank blocked
by air.
Water not hot or
1. Water taken too much
cold enough
in a short time.
2. Power supply cut off
3. Cooling time not
enough.
Water leakage 1. Broken bottle.
2. The transparent
tank and its gas-
kets are not re-
assemble properly
and firmly from last
dismantlement.
Guarantee (only valid within Germany)
The guarantee period for this appliance is 24 months. In the event of demonstrable
defects in materials or manufacture we shall, at our discretion, repair or replace the appli-
ance. If you discover a defect, you should send the appliance to the address listed below,
paying all carriage costs and stating the reason for your complaint. We accept no liability
for any appliances that are uninsured or damaged in transit. Your right to claim a revision
or reduction in price exists only if we are unable to remedy the fault. Indirect damage or
losses are not covered by this guarantee. If the appliance is badly or improperly treated, if
force is used or in the event of damage caused by normal wear and tear the warranty shall
lapse. This is also the case in the event of any third party tampering with the device or of
any changes being made to its original condition. Your receipt is your warranty card and
counts as an official document. If you give false details about the date of purchase or
make any changes to the entries on the receipt you release us from any and all warranty
obligations. The place of fulfilment and jurisdiction is Offenbach am Main.
Date of sale
We hope you will enjoy using your Aquarius Water Dispenser.
If you have any questions, please contact:
BETEC · Bernd Eitel Technologies · Herzogstrasse 55 · 63263 Neu-Isenburg · Germany
Tel: 49 (0) 6102-31067 · Fax: 49 (0) 6102-320859 · www.BETEC-Ideen.de
E-mail: info@BETEC-Ideen.de
5
GB
It is recommended to wait for 3 minutes
before re-starting the cooling function, after
it was shut off, so as to prolong the life
span of the cooling components.
Do not place the water dispenser in damp
room or close to stove. Also keep it away
from direct sunshine and rain.
Solution
1. Refill with water.
2. Press the water button(s) to leave
the faucet open and shake the
unit slightly until water runs out.
1. Wait for some time to allow
sufficient heating and cooling.
2. Wait for some time to allow
sufficient heating and cooling.
3. first cooling time should be 2
hours for drink.
1. Replace a new bottle.
2. Dismantle and assemble again.
Change the aged gaskets when
necessary.
Retailer's stamp