Eaton Cooper Lighting ALL-PRO MST1301LW Instrucciones página 2

OPERATING YOUR FIXTURE
NOTE: Make sure you allow fixture to receive four full
days of sunlight before turning fixture ON.
1. Turn power switch ON.
2. Rotate the sensor assembly to reveal the time
adjustment knob. Rotate knob to "TEST", then
rotate sensor assembly back to desired sensing
direction. (Fig. 5).
NOTE: Fixture has a warm up period of about one
minute. Light will turn on during this period. Once the
light turns off, you are ready to test.
3. Walk across the detection zone at the farthest
distance you wish your sensor to detect motion.
Light will turn off 4 seconds after motion stops.
NOTE: Allow 5 seconds after light turns off before your
next test.
4. Note location of alignment mark on sensor assembly,
then rotate assembly to reveal the time adjustment
knob. Rotate knob to a duration up to 3 minutes, then rotate sensor
assembly back to desired sensing direction. Light will turn ON at night when motion is
detected and turn OFF at the selected time interval after motion stops.
NOTE: When battery is low, the fixture will automatically turn OFF. (The fixture will not turn ON
until the battery has recharged to the operating level.)
PROPER BATTERY CARE AND REPLACEMENT
NOTE: Proper care should ensure the longest possible life for your battery.
• Make sure that your solar panel is located in a sunny location.
• When battery is low, the fixture will automatically turn OFF. (The fixture will not turn ON until
the battery has recharged to the operating level.)
• To ensure proper recharge, turn power switch OFF and allow fixture to receive 4 full days of
sunlight before turning the fixture ON.
To replace the batteries:
1. Replacement batteries must be AA size Ni-MH, with
a capacity of 1800 mA-h. The use of any other type
or size will void your warranty.
2. Turn fixture OFF. Unplug fixture from solar panel
wire. While pressing in on the locking tab at the
bottom of the fixture, lift the fixture up to remove
from the mounting bracket.
3. Use the ribbon provided to gently remove the
batteries. Insert new batteries, being careful to
correctly orient the positive and negative terminals. (Fig. 6)
4. Reinstall the fixture to the mounting bracket, making sure the fixture snaps into the
locking tab. Plug the wire into the solar panel wire, pushing tightly until you hear
two clicks.
5. Prepare the fixture for operation according to the section titled "OPERATING YOUR
FIXTURE" in this instruction manual.
TROUBLESHOOTING
Problem Cause / Solution
Light Does Not Surrounding external ambient light is too bright. (If so, the unit may
think it is daytime.)
Come On With
• Re-aim the head.
Motion At Night
• Relocate or reposition the unit away from the light source.
Fixture is not charging during the day.
• Solar panel must be connected to the connector extending
from the fixture housing when charging.
• Solar panel must receive direct sunlight to charge during
the day (reposition if shadowed).
• Solar panel must be clean and free from debris.
• Make sure batteries have been charged for 4 full days of
sunlight prior to turning the fixure ON.
• When battery is low, the fixture will automatically turn OFF until
the battery is charged to the operating level.
Light Comes On There is motion in the detection zone.
For No Apparent • Make sure the sensor is not picking up moving objects such as
trees, traffic, etc.
Reason At Night
TEST FOR YOURSELF.
• Cover the sensor lens with black electrical tape to prevent
sensor from detecting motion. If the light stays off, something in
the detection zone is triggering the sensor.
• Reposition the sensor.
* If the light stays on with the sensor lens covered, contact
customer service.
Fig. 5
Light Stays On At
A
Night And Does
Not Turn Off
Light Is On
During The Day
ON OFF
1-YEAR LIMITED WARRANTY
THE FOLLOWING WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES,
WHETHER EXPRESS, IMPLIED OR STATUTORY INCLUDING, BUT NOT LIMITED TO, ANY
WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE.
Eaton's Cooper Lighting Business ("Eaton's Cooper Lighting") warrants to customers that, for
a period of five years from the date of purchase, Eaton's Cooper Lighting Business ("Eaton's
ON OFF
Cooper Lighting") products will be free from defects in materials and workmanship. The
obligation of Eaton's Cooper Lighting Business ("Eaton's Cooper Lighting") under this warranty
is expressly limited to the provision of replacement products. This warranty is extended only
to the original purchaser of the product. A purchaser's receipt or other proof of date of original
purchase acceptable to Eaton's Cooper Lighting Business ("Eaton's Cooper Lighting"). This
is required before warranty performance shall be rendered. This warranty does not apply
to Eaton's Cooper Lighting Business ("Eaton's Cooper Lighting") products that have been
altered or repaired that have been subjected to neglect, abuse, misuse or accident (including
shipping damages). This warranty does not apply to products not manufactured by Eaton's
Cooper Lighting Business ("Eaton's Cooper Lighting") which have been supplied, installed,
and/or used in conjunction with Eaton's Cooper Lighting Business ("Eaton's Cooper Lighting")
products. Damage to the product caused by replacement bulbs or corrosion or discoloration of
brass components are not covered by this warranty.
LIMITATION OF LIABILITY:
IN NO EVENT SHALL EATON'S COOPER LIGHTING BUSINESS ("EATON'S COOPER LIGHTING") BE
LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (REGARDLESS OF
Fig.6
THE FORM OF ACTION, WHETHER IN CONTRACT, STRICT LIABILITY, OR IN TORT
INCLUDING NEGLIGENCE), NOR FOR LOST PROFITS; NOR SHALL THE LIABILITY OF EATON'S
COOPER LIGHTING BUSINESS ("EATON'S COOPER LIGHTING") FOR ANY CLAIMS OR DAMAGE
ARISING OUT OF OR CONNECTED WITH THESE TERMS OR THE MANUFACTURE, SALE, DELIVERY,
USE, MAINTENANCE, REPAIR OR MODIFICATION OF COOPER LIGHTING PRODUCTS, OR SUPPLY
OF ANY REPLACEMENT PARTS THEREFORE, EXCEED THE PURCHASE PRICE OF EATON'S
COOPER LIGHTING BUSINESS ("EATON'S COOPER LIGHTING") PRODUCTS GIVING RISE TO A
CLAIM. NO LABOR CHARGES WILL BE ACCEPTED TO REMOVE OR INSTALL FIXTURES.
To obtain warranty service, please contact Eaton's Cooper Lighting Business ("Eaton's Cooper
Lighting"), at 1-800-334-6871, press option 2 for Customer Service, or via e-mail
ConsumerProducts@eaton.com and include the following information:
• Name, address and telephone number
• Date and place of purchase
• Catalog and quantity purchase
• Detailed description of problem
All returned products must be accompanied by a Return Goods Authorization Number issued
by the Company and must be returned freight prepaid. Any product received without a Return
Goods Authorization Number from the Company will be refused. Eaton's Cooper Lighting
Business ("Eaton's Cooper Lighting") is not responsible for merchandise damaged in transit.
Repaired or replaced products shall be subject to the terms of this warranty and are inspected
when packed. Evident or concealed damage that is made in transit should be reported at once
to the carrier making the delivery and a claim filed with them.
Reproductions of this document without prior written approval of Eaton's Cooper Lighting Business ("Eaton's Cooper
Lighting") are strictly prohibited.
For assistance, call 1-800-334-6871 or e-mail us at ConsumerProducts@eaton.com
Printed in China
ARTÍCULOS NECESARIOS
(se compran por separado)
• Destornillador en cruz (Phillips)
CÓMO FUNCIONAS
Durante las horas del día, el panel solar transforma
la luz solar en energía que queda almacenada en el
paquete de la bateríarecargable. Su luminaria cuenta
con un sensor de movimiento, que enciende la luz
cuando es de noche y se detecta algún movimiento.
Esta luminaria está equipada con una fotocélula, que
sólo permite que el artefacto se encienda durante las
horas de la noche.
ADVERTENCIAS Y PRECAUCIONES
INSTRUCCIONES CONCERNIENTES AL RIESGO DE INCENDIO O LESIONES A
LAS PERSONAS:
ATENCIÓN: Para reducir el riesgo de incendio o lesiones personales:
• NO sustituya las baterías.
2
There is motion in the detection zone.
• Make sure the sensor is not picking up moving objects such as
trees, traffic, etc.
• Reposition motion sensor.
* If the light continues to stay on, contact customer service.
The knob on the motion sensor is in the TEST mode.
• Rotate the knob to a duration up to 3 min.
The motion detector is shadowed.
• Reposition motion sensor.
ESPAÑOL
Hasta
35 pies
180 grados