PLYMOVENT ECONOMY ARM Instrucciones Para El Uso página 11

Mounting instructions
1. Bolt mounting bracket to the wall.
Recomended mounting height 1m / 3-4' from floor.
2. Mount arm to wall moounting bracket.
NOTE! THE WASHER
NOTE!
3. Fit hose, jubilee clips, hood collar and hood to the arm.
ball-bearing hose extraction arm
EA-S
ball-bearing hose extraction arm
EA-S
A. If the arm will not stay in the required position:
1. Loose the hose.
2. Pull the extractor out to its full length and angle it horizontally.
Loosen the friction brake until the arm drops towards the floor.
Tighten until it no longer drops
3. If the arm is difficult to move sideways or moves on its own sideways,
then adjustment must be made to the friction collar.
This is done by either loosening or tightening the screw.
A. If the arm will not stay in the required position:
Use an allen key.
1. Loose the hose.
2. Pull the extractor out to its full length and angle it horizontally.
Loosen the friction brake until the arm drops towards the floor.
B. If the outer arm will not stay in the required position:
Tighten until it no longer drops
1. Angle the outer arm horizontally. Loosen the friction brake until the arm
3. If the arm is difficult to move sideways or moves on its own sideways,
drops towards the floor. Tighten until it no longer drops.
then adjustment must be made to the friction collar.
This is done by either loosening or tightening the screw.
Use an allen key.
C. If the hood will not stay in the required position:
1. Loosen the hose.
2. Adjust the friction at C (se picture) until the hood will stay in the exact
B. If the outer arm will not stay in the required position:
position.
1. Angle the outer arm horizontally. Loosen the friction brake until the arm
drops towards the floor. Tighten until it no longer drops.
C. If the hood will not stay in the required position:
0000101886/011013/A EA/S
1. Loosen the hose.
4. Adjust all frictions joints to correct tension.
mAintEnAncE
inStuction
© Copyright 2008: All rights reserved. All information within this printed matter may not be reproduced, 5. Fit hose and jubilee clips.
handed over, copied, xeroxed or translated into another language in any form or means without written
permission from PlymoVent AB. PlymoVent AB reserves the right to make design changes.
mAintEnAncE
ball-bearing hose extraction arm
inStuction
EA-S
© Copyright 2008: All rights reserved. All information within this printed matter may not be reproduced,
EA-S/4/8
handed over, copied, xeroxed or translated into another language in any form or means without written
permission from PlymoVent AB. PlymoVent AB reserves the right to make design changes.
A. If the arm will not stay in the required position:
1. Loose the hose.
2. Pull the extractor out to its full length and angle it horizontally.
Loosen the friction brake until the arm drops towards the floor.
Tighten until it no longer drops
3. If the arm is difficult to move sideways or moves on its own sideways,
then adjustment must be made to the friction collar.
This is done by either loosening or tightening the screw.
Use an allen key.
B. If the outer arm will not stay in the required position:
1. Angle the outer arm horizontally. Loosen the friction brake until the arm
drops towards the floor. Tighten until it no longer drops.
C. If the hood will not stay in the required position:
1. Loosen the hose.
BSAB no: T0.31
Ser.no: EA/DS
Date: sep-98
Replace:
mAintEnAncE
inStuction
BSAB no: T0.31
Ser.no: EA/DS
Date: sep-98
© Copyright 2008: All rights reserved. All information with
Replace:
handed over, copied, xeroxed or translated into another la
permission from PlymoVent AB. PlymoVent AB reserves the
EN - 10