Manual Settings - Hama EWS Intro Instrucciones De Uso

Display
Flashing display
Constant display
No display
• If the station still does not receive a signal, press and hold
the Z/Register button (23) for approximately 3 seconds to
start the manual search for the DCF signal. The DCF radio
symbol (3) begins to ash.
Note – Time settings
• The search process can take up to 10 minutes. If the
search fails, it ends and is repeated at the next clock hour.
The DCF radio symbol (3)
• In the meantime, however, you can set the time and the
date manually.
• The clock automatically continues to search for the
DCF signal on a daily basis (between 2 am and 4 am
and between 5 am and 6 am). If the signal is received
successfully, the manually set time and date are
overwritten.
Note – Summer time
The clock automatically switches to summer time.
appears on the display as long as summer time is activated.

Manual settings

• Press and hold the CLOCK button (21) for approximately 3
seconds to make the following settings one after the other:
• 12 or 24-hour format
• Weekday language (GE = German, FR = French,
ES = Spanish, IT = Italian, EN = English)
• Time zone (from -12 to +12 hours CET)
• Hour
• Minute
• Second
• Year
• Month
• Day
Press the SET/RESET button (25) to select your setting. Press
the CLOCK button (21) to con rm your entries.
4
Search for the DCF signal
Active
Successful –
signal is being received
Inactive
goes out.
Note – Time zone
• The DCF signal can be received over long distances, but
always transmits the current Central European Time in
Germany. Make sure you account for the time difference
in countries in other time zones.
• If you are in Moscow, the time is 3 hours later than in
Germany. This means that you should set +3 for the time
zone. The clock then sets the time automatically to 3
hours ahead after receiving the DCF signal or according to
the manually set time.
Alarm
• Press and hold the ALARM button (22) for approximately
3 seconds to set the time of the alarm displayed. The hours
display begins to ash.
• Press the SET/RESET button (25) to select the hour for
the alarm time and con rm your selection by pressing the
ALARM button (22). The minutes display begins to ash.
• Repeat the process to set the minutes for the alarm time.
• Repeat the entire process to set the second alarm.
• If you do not make an entry for 25 seconds, you
automatically exit the setting mode.
• Press the ALARM button (22) once to display the rst alarm
time. Press the ALARM button (22) once more to display the
second alarm time.
• Press the SET/RESET button (25) once to activate the rst
alarm. Press the SET/RESET button (25) once more to
activate the second alarm. Press the SET/RESET button (25)
a third time to activate both alarms.
• An activated alarm is indicated by the respective symbol
/ on the display.
1
2
• Press the SET/RESET button (25) repeatedly to deactivate
the daily alarm. The alarm symbol
• If the alarm is triggered, the alarm symbol is displayed and
an alarm will sound.
• Press SELECT (24), SET/RESET (25), ALARM (22) or CLOCK
(21) to stop the alarm. Otherwise, it will stop automatically
after 2 minutes.
Note – Snooze function
• While the alarm is sounding, press the Z/Register button
(23) to activate the snooze function. The snooze symbol
z
Z
and alarm symbol
display. The alarm signal will stop for approximately 5
minutes, after which it will sound again.
• Press the SELECT button (24) to stop the snooze function
and the alarm.
Temperature (Celsius/Fahrenheit)
• Press and hold the SELECT button (24).
• Press the SET/RESET button (25) to choose between °C and
°F for the temperature display.
• Con rm your selection by pressing the SELECT button (24).
• The weather station indicates a trend as to how the values
for the outdoor temperature and room temperature are likely
to develop over the next few hours.
/ is not displayed.
1
2
begin to ash on the
/
1 2