Technical Data; General Description; Processable Materials - IMER SMART CUT 350 Manual De Uso & Mantenimiento

Dear Customer,
Congratulations on your choice of purchase: IMER saws are the result
of years of experience and are equipped with all the latest technical
innovations.
- WORKING IN SAFETY
To work in complete safety, read the following instructions
carefully.
To work in complete safety, read the following instructions carefully
before using the machine.
The manual is considered part of the machine and must be stored for
future reference (EN 12100-2) through to scrapping of the machine
itself. Should the manual be lost or damaged, a replacement copy can
be ordered from the manufacturer.
The manual contains important information regarding site preparation,
machine use, maintenance procedures, and requests for spare parts.
Nevertheless, the installer and the operator must both have adequate
experience and knowledge of the machine prior to use. In order to ensure
operator safety, safe operation and long service life, all instructions in
this manual must be observed, together with the requirements of current
legislation governing work safety (use of safety footwear and adequate
clothing, use of helmets, gloves, goggles etc.).
- Make sure that all signs are legible.
- It is strictly forbidden to carry out any form of modifi cation to
the steel structure or working parts of the machine.
IMER INTERNATIONAL declines all responsibility for failure to comply
with laws and standards governing the use of this equipment, in
particular; improper use, defective power supply, lack of maintenance,
unauthorised modifi cations, and partial or total failure to observe the
instructions contained in this manual.
IMER INTERNATIONAL reserves the right to modify features of the saw
and contents of this manual, without the obligation to update previous
machines and/or manuals.

1. TECHNICAL DATA

Technical data are stated in table 1 and electrical specifi cations in table
2.
Table 1 - TECHNICAL DATA
Model
Max. blade diameter
Diamond Blade hole diameter
Single phase 115V/60Hz motor power
Max. blade rotation speed (115V/60HZ)
Cutting table dimensions
Length of 90° cuts (thickness= 10mm)
Maximum cutting depth of dia. 350 disc with 1-2
passes
Water pump fl ow rate
Water tank capacity
Machine dimensions
Packed machine dimensions
Weight with packaging
IMER U.S.A. Inc.
SMART CUT 350 14"
2. DESIGN AND CONSTRUCTION STANDARDS
Combi 250 VA saws have been designed and manufactured according
to the following standards: UNI EN 12418:2001; EN 12100-1/2:2005;
EN 60204-1:2006.
3. NOISE LEVEL AND VIBRATIONS
Table 3 gives the sound pressure level of the machine measured at
the ear of the operator when running under no load (L
transmitted when it is operating.
4. GENERAL SAW DESCRIPTION

4.1 General description

The SMART CUT 350 14" sawing machine is composed of a frame
(Fig.1, Ref.A)
(Fig.1, Ref.C) is mounted to a pillar and can be rotated up and down
through 32° by slackening off the handwheel (Fig.1, Ref.D). The sawing
machine is fi tted with a blade guard (Fig.1, Ref.E) to guarantee optimal
safety during operation and to protect the user during cutting cycles.
The carriage (Fig.1, Ref.F) used to support the material being cut runs
on the frame's rails. It mounts the goniometer (Fig.1, Ref.G) for making
cuts at different angles. A plastic impact-resistant tank (Fig.1, Ref.H) is
mounted under the frame. The immersion water pump (Fig.1, Ref.I) is
housed inside the tank and supplies water to the nozzles (Fig.1, Ref.L)
SMART CUT 350 14"
mounted on the blade guard which cool the disc during cutting. A valve
350 mm
(Fig.1, Ref.M) is mounted above the blade guard to adjust the fl ow rate
25.4 mm
of water delivered to the cutting
1,5 kW
1870 rpm

4.2 Processable materials

510X410mm
The sawing machine has been designed for cutting the following
materials: brick, ceramic, marble, granite, articles in cement and similar
500 mm
of a size compatible with the length, cutting depth and dimensions of the
107/204mm
table specifi ed in table 1. Maximum weight of processable materials:
35 kg.
13 l/min
40 L
5. OPERATION SAFETY
1186x722x850 mm
1196x732x895 mm
102 Kg fi tted.
explosions or fi re.
The saw is not fi tted with specifi c lighting and therefore the workplace
must be suffi ciently lit for this purpose (min. 300 lux).
The power lines must be laid to prevent any possible damage.
Ensure that the electrical connection is protected against the risk of
water penetration in connectors. Only use connectors and couplings
equipped with spray guards.
Never use inadequate or makeshift electrical lines or cables without
earthing; if in doubt consult a specialised technician.
Repairs to the electrical installation must be performed exclusively by
specialised personnel Disconnect the machine from the power supply
before performing maintenance or repairs.
6. GENERAL SAFETY WARNINGS
This machine was designed to provide the best performance and the
highest degree of safety: however, it is up to the operator to ensure this
safety, by taking due care during all work phases. The following are
recommended:
3
Table 2
Feature
Power (kW)
Rated voltage (V)
Frequency (Hz)
Absorbed current (A)
Number of poles
Motor speed (rpm)
Service type
Insulation class
Protection class
Capacitor (μF)
Table 3
Model Type of motor
SMART CUT 350 14" Electric
supported by folding legs (Fig.1, Ref.B). The cutting head
blade.
- Before using the saw, ensure that all protection devices are
- Never use the saw in environments subject to the risk of
Motor (115V/60Hz)
1,5
115
60
14.4
2
3400
S6 40%
F
IP55
120 (Ø 50x120)
) and vibrations
pA
L A
pA eq
86 dB 2.57 m/s 2