SILENTRON SILENT DUALTECH 5514 Manual De Usuario página 5

WIRELESS DOUBLE TECHNOLOGY DETECTOR FOR OUTDOOR USE
GENERAL NOTICES - Read carefully before using the appliances
Installation must be performed by qualified technical staff and can be subject to specific technical Standards, depending on the country
Batteries Rechargeable accumulators and/or batteries of any type: these appliances use accumulators or batteries, which are potentially
dangerous as they are pollutant, therefore dangerous to the health of the public. Replace the accumulators and/or batteries exclusively with
same models, position and connect them respecting the polarity indicated in the instructions. It is mandatory to dispose of accumulators/waste
batteries according to the Standards in force. This is also the case when the machines must be scrapped. The accumulators/batteries must be
previously removed, returning them to the appliance dealer or depositing them in the relevant containers made available by the distribution
network. If liquid should escape from the batteries or accumulators, use silicone gloves to protect the hands and prevent injury.
Liability: the manufacturer declines all liability consequent to no use or installation and incorrect use of the appliances supplied.
Warranty: 3 years, within the terms described in the Main Catalogue, batteries and accumulators excluded.
1. CONDITIONS FOR USE AND INSTALLATION CRITERIA:
Silent Dual Tech is a detector with double technology (PIR = passive infra-red detector + MW = microwave Doppler detector) developed to
indicate the approach of a human target or similar in movement in the protected area and it has been designed for use in outdoor areas with the
purpose of supplying an anti-approach pre-alarm in the case of intrusion. The use of the two detection technologies allows the appliance to
reduce the possibility of improper alarms, due to typical environmental factors linked to outdoor installation (movement of animals of all types,
movement of objects generated by meteorological phenomenon). Precise positioning and correct regulation of the appliance are fundamental for
this scope: in extreme cases it is possible to reduce these alarms even further by installing two opposite appliances in AND to protect the same
area (solution envisioned by the Silentron control panels).
Brackets and supports: the moveable joint code 5961 and the corner bracket code 8086 are useful accessories that can favour correct
positioning, which excludes the probability of movements in the protected area as much as possible.
2. FUNCTIONING
a) General features: the appliance functions with 3 AA alkaline batteries and transmits the alarm via radio, therefore connection wires are not
required. The PIR part of the appliance always functions and activates the MW part if intrusion is detected: the Doppler confirmation of the
existence of a moving mass in the area generates the alarm state. The detection sequence is displayed by the LED on the front of the
appliance, which changes colour (green-orange-red) through the various passages.
Block for the reduction of consumption: after every alarm the appliance is momentarily blocked. This is restored after 2 minutes with no
movement in the area. This is to reduce consumption in busy areas.
b) Adjustments: the PIR part can be adjusted in RANGE and in PULSE COUNTS, which constitutes an intervention delay. The MW is
adjusted in RANGE and DELAY, which is the minimum duration time of the movement detected at the end of the alarm.
c) Anti-removal protection: a relevant magnet, to be fixed to the wall in the point envisioned on the sliding bracket, allows anti-removal
protection. When the detector is correctly positioned on the bracket, the magnet closes a reed positioned inside the appliance: upward or
downward sliding and/or the detachment of the appliance from the wall causes a "tampering" alarm and the successive "test" state. In the case
of detector installation with brackets or joint accessory, the magnet must be correctly positioned using installation mechanisms in order to allow
the TEST, as well as realising the protection.
d) Anti-opening protection: by opening the powered appliance, a relevant button controls the transmission of tampering independently from
the condition of the anti-removal magnet.
e) Appliance test conditions (TEST): Silent DualTech is in TEST mode when it is removed from its slide, behind which the magnet is located,
joined to the fixing surface: this causes the tampering alarm, it is therefore necessary to previously put the control panel in test mode. The test
state lasts 3 minutes successively to the correct re-positioning of the appliance and via LED displays all of the detections, annulling the block
after a first alarm.
Attention! Where it is not possible to install the anti-removal magnet, it must be held manually on the back of the appliance in the correct
position for at least 6 seconds with the appliance powered, in order to activate the control (confirmation beep). Successively it will be sufficient to
position the magnet in position and move it away for 1 second in order to activate the TEST state.
Attention! The appliance remains permanently in TEST when the anti-opening contact is open.
f) Supervision: SILENT Dual Tech transmits an operating status signal about every 40 minutes, which is managed by the SILENTRON
supervised control panels - see "supervision function" of the control panels used.
g) Low Battery signal: the appliance signals via radio to the control panel and locally using 5 beeps that the batteries must be replaced.
3. START-UP - respect the sequence of the operations
a) Programming the appliance on the control panel or receiver (also see the instructions of the control panel/receiver used):
•
Open the appliance by loosening the screws on the bottom and open the lid of the battery compartment.
•
Place the control panel in PROGRAMMING mode, in detector learning condition on the desired zone
•
Extract the battery isolating film, powering the appliance: programming will be confirmed by a Beep from the control panel.
•
Terminate the procedure by assigning the name to the detector (written and vocal label on the control panels). Close the battery
compartment.
SILENTRON – Made In Italy
COPYRIGHT SILENTRON DF5514XA090723MF
5