Black and Decker LD120 Manual De Instrucciones página 24

24 • ENGLISH
1. Plug the charger into an appropriate outlet before
inserting the battery pack.
2. Insert the battery pack into the charger as shown in
Fig. B.
3. The green LED will flash indicating that the battery
is being charged.
4. The completion of charge is indicated by the green
LED remaining on continuously. The pack is fully charged
and may be used at this time or left on the charger.
Recharge discharged batteries as soon as possible
after use or battery life may be greatly diminished.
For longest battery life, do not discharge batteries
fully. It is recommended that the batteries be recharged
after each use.
Leaving the battery in the charger
The charger and battery pack can be left connected with
the green LED glowing indefinitely. The charger will keep
the battery pack fresh and fully charged.
Installing and removing the battery pack
from the tool
Warning! Make certain the lock-off button is engaged
to prevent switch actuation before removing or installing
battery.
To install battery pack:
Insert battery pack into tool until an audible click is heard
(Fig. C).
To remove battery pack:
Depress the battery release button as shown in Fig. D
and pull battery pack out of tool.
SAFETY WARNINGS AND INSTRUCTIONS:
1. Hold drill firmly with one hand on the grip
and the other hand on the bottom of the battery pack.
2. When attaching accessories in the drill chuck,
hand tighten the keyless chuck firmly.
Warning! Drill may stall (if overloaded or improperly
used) causing a twist. Always expect the stall. Grip the drill
firmly with both hands to control the twisting action and
prevent loss of control which could cause personal injury.
If a stall does occur, release the trigger immediately and
determine the reason for the stall before re-starting.
OPERATING INSTRUCTIONS
Trigger switch and reversing button (Fig. E )
f The drill is turned ON and OFF by pulling and
releasing the trigger switch (1). The farther the trigger
is depressed, the higher the speed of the drill.
DRILLS
f A Forward/Reverse control button (2) determines
the direction of the tool and also serves as
a lock off button.
f To select Forward rotation, release the trigger switch
and depress the Forward/Reverse control button
to the left.
f To select reverse, depress the Forward/Reverse
control button the opposite direction.
Note: The center position of the control button
locks the tool in the off position. When changing the
position of the control button, be sure the trigger is
released.
Torque control (Fig. F)
This tool is fitted with a torque adjustment collar (3)
to select the operating mode and to set the torque for
tightening screws. Large screws and hard workpiece
materials require a higher torque setting than small screws
and soft workpiece materials.
f For drilling in wood, metal and plastics, set the collar
to the drilling position symbol.
f For screwdriving, set the collar to the desired setting.
If you do not yet know the appropriate setting, proceed
as follows:
a. Set the collar to the lowest torque setting.
b. Tighten the first screw.
c. If the clutch ratchets before the desired result
is achieved, increase the collar setting
and continue tightening the screw.
f Repeat until you reach the correct setting.
Use this setting for the remaining screws.
Keyless chuck (Fig. G)
Warning! Make certain the lock-off button is engaged
to prevent switch actuation before installing or removing
accessories.
To insert a drill bit or other accessory:
1. Grasp the rear half of the chuck (4) with one hand and
use your other hand to rotate the front half (4a) in
the counterclockwise direction, as viewed from
the chuck end.
2. Insert the bit or other accessory fully into the chuck,
and tighten securely by holding the rear half of the
chuck and rotating the front portion in the clockwise
direction as viewed from the chuck end.
Warning! Do not attempt to tighten drill bits (or any other
accessory) by gripping the front part of the chuck and
turning the tool on. Damage to the chuck and personal
injury may occur when changing accessories.
SCREWDRIVING
For driving fasteners, the reversing button should be
pushed to the left. Use reverse (button pushed to the right)