Worx WG268 Manual Del Usuario página 10

5. To REMovE oR iNSTaLL BaTTERy
PaCk (See Fig. E)
Depress the Battery Pack Release Button (4) to
remove the Battery Pack (3) from your Hedge
Trimmer. After recharging, insert the Battery
Pack into trimmer's battery port. A simple push
and slight pressure will be sufficient. Check to
see if the battery is fully secured.
6. BaTTERy STaTuS LEd'S (See Fig. F )
NoTE: The Status LEd's will indicate the
battery condition when the button on the
battery is pressed.
The LED's constantly senses and displays the
battery condition as follows:
Press the button "POWERTEST" , the light
button is illuminated.
When the three green lights are illuminated,
the battery is in a highly charged condition.
When two lights (
battery is in a moderately charged condition.
When only one green light ( ) is illuminated,
the battery charge is depleted.
iMPoRTaNT:
when only one light is illuminated,
10
your battery is overly discharged, even
though the hedge trimmer may still be
capable of trimming hedge. Continuing
to operate your trimmer with the battery
in this discharged condition may reduce
the life and performance of your battery.
7. STaRTiNG aNd SToPPiNG
BEFoRE STaRTiNG youR HEdGE
TRiMMER
Remove Blade Sheath (9).
To STaRT youR HEdGE TRiMMER
Your Hedge Trimmer is equipped with both
Rear and Front Switch levers. Both switch
levers need to be pressed for the Hedge
Trimmer to start. Depress and hold the Front
Switch Lever (5) and press the Rear Switch
Lever (2) (See Fig.G).
To SToP youR HEdGE TRiMMER
Move Hedge Trimmer away from cutting area
before stopping.
To stop, release one of the switch levers (See
Fig. H).
waRNiNG: if any parts are missing,
damaged or broken, do not operate
Cordless Li-ion hedge trimmer
) are illuminated, the
your hedge trimmer until all damaged
parts have been replaced or repaired.
Failure to do so could result in serious
personal injury. do NoT uSE wiTHouT
HaNdLE aNd GuaRd
8. How To uSE youR HEdGE TRiMMER
Note that the Front Switch Lever (5) can be
activated on three sides, giving you many
choices for a comfortable grip. Before cutting
an area, inspect it first and remove any
foreign objects that could become thrown
or entangled in the blades. Always hold the
trimmer with both hands and with the blade
away from you before turning it on.
When trimming new growth, use a wide
sweeping action so that the stems are fed
directly into the blade. (See Fig. I&J)
Allow the cutting blades to reach full speed
before cutting. When operating, keep the
cutting blades away from people and objects
such as walls, large stones, trees, vehicles, etc.
If the blade stalls, immediately stop the
trimmer. Release the two Switch Levers (5 &
2) before attempting to clear jammed debris
from the cutting blades.
Wear gloves when trimming thorny or prickly
growth.
Do not attempt to cut stems that are too thick
for the cutting blade.
ToP CuTTiNG
Use a wide sweeping motion (See Fig. I). A
slight downward tilt of the cutting blades in
the direction of motion gives the best cutting
results.
SidE CuTTiNG
When trimming the sides of the hedge,
begin at the bottom and cut upwards (See
Fig. J), tapering the hedge inward at the top.
This shape will expose more of the hedge,
resulting in a more uniformed growth.
9. CLEaNiNG
REMOVE THE BATTERY PACK (3). Use a soft
brush to remove debris from all air intakes
and cutting blade.
Wipe the surface with a dry cloth.
waRNiNG: Never use water for
cleaning your trimmer. Do not clean with
chemicals, including petrol, or solvents as this
EN