Electrical Safety; Personal Safety - Silverline 270289 Manual De Instrucciones

270289

Electrical Safety

a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not
use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and
matching outlets will reduce risk of electric shock
b) Avoid body contact with earthed or grounded surfaces, such as pipes, radiators,
ranges and refrigerators. There is an increased risk of electric shock if your body is
earthed or grounded
c) Do not expose power tools to rain or wet conditions. Water entering a power tool
will increase the risk of electric shock
d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the
power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged
or entangled cords increase the risk of electric shock
e) When operating a power tool outdoors, use an extension cord suitable for outdoor
use. Use of a cord suitable for outdoor use reduces the risk of electric shock
f) If operating a power tool in a damp location is unavoidable, use a residual current
device (RCD) protected supply. Use of an RCD reduces the risk of electric shock

Personal Safety

a) Stay alert, watch what you are doing and use common sense when operating a
power tool. Do not use a power tool while you are tired or under the influence of
drugs, alcohol or medication. A moment of inattention while operating power tools
may result in serious personal injury
b) Use personal protective equipment. Always wear eye protection. Protective
equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal injuries
c) Prevent unintentional starting. Ensure the switch is in the off-position before
connecting to power source and/or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or energising power tools that have
the switch on invites accidents
d) Remove any adjusting key or wrench before turning the power tool on. A wrench
or a key left attached to a rotating part of the power tool may result in personal injury
e) Do not overreach. Keep proper footing and balance at all times. This enables better
control of the power tool in unexpected situations
f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and
gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in
moving parts
g) If devices are provided for the connection of dust extraction and collection
facilities, ensure these are connected and properly used. Use of dust collection can
reduce dust-related hazards
Power Tool Use & Care
a) Do not force the power tool. Use the correct power tool for your application. The
correct power tool will do the job better and safer at the rate for which it was designed
b) Do not use the power tool if the switch does not turn it on and off. Any power tool
that cannot be controlled with the switch is dangerous and must be repaired
c) Disconnect the plug from the power source and/or the battery pack from the
power tool before making any adjustments, changing accessories, or storing
power tools. Such preventive safety measures reduce the risk of starting the power
tool accidentally
d) Store idle power tools out of the reach of children and do not allow persons
unfamiliar with the power tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained users
e) Maintain power tools. Check for misalignment or binding of moving parts,
breakage of parts and any other condition that may affect the power tool's
operation. If damaged, have the power tool repaired before use. Many accidents
are caused by poorly maintained power tools
f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are easier to control
g) Use the power tool, accessories and tool bits etc. in accordance with these
instructions, taking into account the working conditions and the work to be
performed. Use of the power tool for operations different from those intended could
result in a hazardous situation
WARNING: When used in Australia or New Zealand, it is recommended that this tool
is ALWAYS supplied via Residual Current Device (RCD) with a rated residual current of
30mA or less.
Service
a) Have your power tool serviced by a qualified repair person using only identical
replacement parts. This will ensure that the safety of the power tool is maintained
600W Multipurpose Router
Additional Safety for Routers
a) Hold the power tool by insulated gripping surfaces to prevent electric shock if the tool
cuts through its own power cord or other power cable
b) Clamp the workpiece to a stable platform. Holding the workpiece by hand or against
the body may lead to loss of control
c) Use safety equipment including safety goggles or shield, ear protection, dust mask and
protective clothing including safety gloves
d) Cloths, cord, string etc should never be left around the work area
e) Ensure the mains supply voltage is the same as the tool rating plate voltage
f) Ensure any cable extensions used with this tool are in a safe electrical condition, and
have the correct ampere rating for the tool
g) Completely unwind cable drum extensions to avoid potential overheating
h) Use appropriate detectors to determine if utility cables or pipes are below the surface
of the work area. Consult utility companies for assistance if necessary. Contact with
electric cables can lead to electric shock and fire. Damaging a gas pipe can lead to
explosion. Contact with water lines can lead to major property damage
i) Ensure embedded objects such as nails and screws have been removed from the
workpiece before commencing operation
j) Handle router bits with care as they can be extremely sharp
k) Before use, check the bit carefully for signs of damage or cracks. Replace damaged or
cracked bits immediately
l) Ensure router cutters/bits are sharp and maintained correctly. Dull cutting edges can
lead to uncontrolled situations including stalling, increased heat and possible injury
m) ALWAYS use both handles and maintain a firm grip on the router before proceeding
with any work
n) Keep handles and gripping surfaces dry, clean and free of oil and grease to ensure the
tool can be securely held in use
o) Before using the tool to make a cut, switch on and let it run for a while. Vibration could
indicate an improperly installed bit
p) Take notice of the direction of rotation of the bit and the direction of feed
q) Keep your hands away from the routing area and router bit cutter. Hold the auxiliary
handle or an insulated gripping surface with your second hand
r) NEVER start the router while the cutter is touching the workpiece
s) Ensure the plunge spring is always fitted when using hand-held
t) Ensure the cutter has completely stopped before plunging to the collet lock position
u) The maximum speed of the router bit/cutter must be at least as high as the maximum
speed of the power tool
v) Parts of the router bits may become hot during operation. Do not handle immediately
after use to avoid risk of burns
w) Do not allow parts to come into contact with combustible materials
x) The shank size of the router cutter/bit must be matched to the exact same size collet
fitted to the router. Incorrectly fitted router cutter/bits will rotate irregularly and have
increased vibration that could lead to loss of control
y) DO NOT press the spindle lock button, or attempt to switch the tool into bit change
mode while the router is operating
z) Keep pressure constant while cutting into the workpiece, allowing the router bit cutter
to dictate the speed of cut. DO NOT force the tool and overload the motor
aa) Ensure rating labels and safety warnings on the tool remain clear to read and are
replaced if marked or damaged
bb) When operating the router, be prepared for the router bit cutter stalling in the workpiece
and causing loss of control. Always ensure the router is firmly held and the on/off
switch is immediately released in such circumstances
cc) After switching on the router, check the router bit is rotating evenly (not 'wobbling') and
there is no additional vibration due to the router bit being incorrectly fitted. Operating
the router with an incorrectly fitted router bit can lead to loss of control and severe
injury
dd) EXTREME care must be taken when using cutters with a diameter greater than 2"
(50mm). Use very slow feed rates and/or multiple shallow cuts to avoid overloading the
motor
ee) ALWAYS switch off and wait until the bit has come to a complete standstill before
removing the machine from the workpiece
ff) Disconnect from power before carrying out any adjustment, servicing or maintenance
WARNING: Dust generated by using power tools can be toxic. Some materials may be
chemically treated or coated and be a toxic hazard. Some natural and composite materials
may contain toxic chemicals. Some older paints may contain lead and other chemicals.
Avoid prolonged exposure to dust generated from operating a router. DO NOT allow dust to
get onto skin or eyes and do not allow the dust to enter your mouth to prevent absorption
of harmful chemicals. Where possible, work in a well-ventilated area. Use a suitable dust
mask and dust extraction system where possible. Where there is a higher frequency of
exposure, it is more critical that all safety precautions are followed and a higher level of
personal protection is used.
www.silverlinetools.com
5