Bestway 58367 Manual De Instrucciones página 3

A
C
D
CONTROL VALVE OVERVIEW
WARNING: To prevent equipment damage and
possible injury, always switch off sand filter before
changing the Control Valve function. Changing
valve positions while the pump is running can
damage the Control Valve, which may cause
personal injury or property damage.
How to Use the Control Valve:
Press down on the Control Valve handle and rotate
to desired function.
CONTROL VALVE FUNCTIONS
The Control valve is used to select 6 different filter
functions: Filter, Rinse, Circulate, Backwash,
Closed and Drain.
Filter: This function is used to filter pool
water and should be positioned here 99%
of the time. Water is pumped through the
sand filter, where it is cleaned and returned
to the pool.
Backwash: This function is used to clean
the sand bed; water is pumped down
through the Collector Hub, upwards through
the sand bed, and deposited out of Port D.
Rinse: This function for initial startup,
cleaning, and sand bed leveling after
Backwash; water is pumped downwards
through the sand bed, up through the
Collector Hub and deposited out of the
valve Port D.
Circulate: This function circulates pool water
bypassing the sand filter; use this function if
the filter is broken to collect debris in the
Debris Screens.
NOTE:
• Be sure all provisions for wastewater disposal meet applicable local, state or national codes. Do not discharge water where it will cause flooding or
damage.
• When the Control Valve is set to the Backwash, Rinse, or Drain position, water will discharge from Port D on the Control Valve.
• Do not switch on or operate the sand filter with the Control Valve set to the Closed function or it will seriously damage the sand filter.
• Do not set the Control Valve between two functions, or it will lead to leaking.
• To avoid water leakage, screw the Port D Cap onto the Control Valve Port D before operating the sand filter.
HOSE ADAPTOR FUNCTIONS
Pool with Valves (Ф3.2cm)
1. Connect the Adaptors (21) to the Hose.
2. Place the loose Hose Clamps (22) in the end of Hose with Adaptor (21).
21
PARTS REFERENCE OVERVIEW
Before assembling the sand filter, take a few minutes to become familiar with all the sand filter parts.
1
2
3
4
5
6
7
8
9
10
27 22
22
SPECIFICATIONS
437m m
633 m m
Drain: This function drains water from the
pool; another filter bypass setting, water is
pumped and deposited out of Port D,
instead of returning it to the pool.
>1/2 in
>1/2 in
or
A
A
P61318
P61318
B
B
P61322
P6680
11
12
13
14
15
16
17
18
19
12
12
20
12
22
22 27
P6680 P61322
28 25 28
Filter Diameter:
Effective Filter Area:
Max. Operating Pressure:
Working sand filter pressure:
Max. Water Temperature:
Sand:
Sand Size:
Sand Capacity:
3
DESCRIPTION
REF.NO.
1 Control Valve
26
2 Pressure Gauge
3 Flange Clamp
21
4 Hub Cover
5 Tank
6 Hub
22
7 Pollution cartridge
8 Drain Washer
9 Drain Valve Cap
10 Tank base
11 Garden Hose Adaptor
23
12 Washer
13 Port D Cap
14 Piping
15 O-Ring
16 Strainer Cover
17 Strainer
18 Filter Cartridge
19 Seal Ring
20 Pump
21 Adaptor
22 Hose Clamps
23 Hose (Ф38mm)
26 Adapter Nut
OPTIONAL PARTS
12 Washer
24
22 Hose Clamps
Debris Screen
24 Debris Screen
P61318
Debris Screen
25 T-Joint
27 Hose (Φ32mm)
28 O-Ring
437mm
0.150m ( 1.61ft
2
1.58Bar( 23PSI)
<0.56Mpa( 8PSI)
35°C
Not included
#20 silica sand,0.45-0.85mm
Approximately 35kg
Closed: This function stops water
flowing between the sand filter and
the pool.
1.2 inch<
22
SPARE
QTY.
PART NO.
1 P61204
1 P61138
2 P61205
1 P61209
1 P61213
1 P61206
1 P61211
1 P6581
1 P6580
1 P61212
1 P6614
5 P6029
1 P6540
1 P6560
1 P61214
1 P6561
1 P6562
8 P61210
1 P6563
1 P61208
2 P6916
4 P6124
2 P6517
1 P6615
1 P6029
1 P6124
2 P6680
1 P61318
1 P61322
1 P61408
2 P6019
2 P6005
)
2
S-S-004292