Technical Data; Warranty Certificate - EMAK BT 5500 Manual De Instrucciones

mind that with the bushes inserted one inside the other, the
slots must always be lined up one against the other.
• Use only original replacement parts.
WARNING – If you are unable to perform the above
operations, contact an Authorised Service Centre.

TECHNICAL DATA

Models
Engine
Power
Displacement
Maximum cutting Ø
Dimensions
Weight
Sound pressure*
Sound power*
* Measured with dry Norway spruce wood Ø 20x30 mm at a
distance of 1 m and a height of 1.6 m in accordance with Machine
Noise Regulation 3. GSGV 1 para. 2 No. 1d)
TROUBLESHOOTING
A) Th e machine doesn't start and doesn't make any sound.
Solution: Check that there is petrol in the fuel tank. Check that
the bolts securing the cover of the hammer assembly are fully
tightened. If they are not suffi ciently tightened, the safety switch
cannot be deactivated and therefore the electrical circuit will
not function correctly. Warning! Never fi t the bolts without
the plastic safety washer and rosette. Overtightening them can
irreparably damage the switch. If the fault cannot be eliminated,
for machines with petrol engines proceed in accordance with the
engine constructor's instructions.
B) Th e machine doesn't start.
Solution: Check whether the hammer assembly is able to rotate
freely. If it is, contact your nearest Authorised Dealer because
the engine is probably damaged and may require servicing by an
Authorised Service Centre.

WARRANTY CERTIFICATE

Th is machine has been designed and manufactured using the
most modern techniques. Th e manufacturer guarantees the
machine to be free from defects for a period of twenty-four
(24) months from the date of purchase provided it is used
exclusively for private/hobby purposes. If the machine is used
for professional purposes, the warranty period shall terminate
aft er a period of six (6) months. If the machine is used for hire,
the warranty period shall terminate aft er a period of three (3)
months.
Limited warranty
1) Th e warranty period starts on the date of purchase. Th e
manufacturer, acting through the sales and technical
MODEL
SERIAL N.
BOUGHT BY MR/MS
Do not send! Only attach to requests for technical warranties.
SH 550 – BT 5500
OHV petrol
3.6 kW
163 cm3
60 mm
134 x 55 x 94 cm
80 kg
88 dB (A)
95 dB (A)
assistance network, shall replace free of charge any parts
proven defective in material, machining or manufacturing.
Th e warranty does not aff ect the purchaser's rights as
established under legislation governing the consequences of
defects in the machine.
2) Technical personnel will undertake the necessary repairs in
the minimum time possible, compatible with organisational
needs.
3) To make any claim under the warranty, this certifi cate of
warranty, fully completed, bearing the dealer's stamp and
accompanied by the invoice or receipt showing the date of
purchase, must be displayed to the personnel authorised
to approve work.
4) Th e warranty shall be null and void if:
− the machine has evidently not been serviced correctly,
− the machine has been used for improper purposes or has
been modifi ed in any way,
− unsuitable lubricants and fuels have been used.
− non-original spare parts and accessories have been fi tted,
− work has been done on the machine by unauthorised
personnel.
5) Th e warranty does not cover consumables or parts subject to
normal wear.
6) Th e warranty does not cover work to update or improve the
machine.
7) Th e warranty does not cover any preparation or servicing
work required during the warranty period.
8) Damage incurred during transport must be immediately
brought to the attention of the carrier: failure to do so shall
render the warranty null and void.
9) Engines of other manufacturers (Briggs & Stratton,
Tecumseh, Kawasaki, Honda, etc.) fi tted to our machines
are covered by the warranties of the engine manufacturer.
10) Th e warranty does not cover injury or damage caused
directly or indirectly to persons or things by defects in the
machine or by periods of extended disuse of the machine
resulting from the said defects.
EC DECLARATION OF CONFORMITY in accordance with
Directive 89/392/EEC
Th e undersigned
EMAK spa Via Fermi, 4 – Bagnolo in Piano (RE) – ITALY
declares under its sole responsibility that the
bioshredders SH 550 – BT 5500
serial number identifi cation 10-072101÷10-072250
conforms with the provisions of the following harmonised
standards: EN 13683:2003
conform to the requirements of Directives
2000/14/EC – 89/336/EC - 98/37/CE
Guaranteed sound power level: 95 dB (A)
Bagnolo in Piano (RE)
ITALY, 01/01/2008
Giacomo Ferretti – Chairman Emak
DATE
DEALER
S.P.A.
GB
7