Air Supply And Connections; Loading Tool; Warranty; Additional Limitations - Husky DPFR2190 Guía De Uso Y Cuidado

Safety Information(Continued)

AIR SUPPLY AND CONNECTIONS

1.
The connector on the tool must not hold pressure when
air supply is disconnected. If an incorrect fitting is used,
the tool can remain charged with air after disconnecting
and thus will be able to drive a fastener even after the air
line is disconnected, possible causing injury.
2. Do not use any type of reactive gases, including, but not
limited to, oxygen and combustible gases, as a power
source. Use filtered, lubricated, regulated compressed air
only. Use of a reactive gas instead of compressed air may
cause the tool to explode which will cause death or
serious personal injury.
3.
Use only a pressure-regulated compressed air source to
limit the air pressure supplied to the tool. The regulated
pressure must not exceed 115 psi. If the regulator fails,
the pressure delivered to the tool must not exceed 200
psi. Over pressurizing the tool is able to result in bursting,
abnormal operation, breakage of the tool or serious injury
to persons. Use only clean, dry, regulated compressed air
at the rated pressure or within the rated pressure range
as marked on the tool. Always verify prior to using the
tool that the air source has been adjusted to the rated air
pressure or within the rated air-pressure range.
4. Always disconnect air source:
Before unloading or making adjustments.
When maintaining the tool.
When clearing a jam.
When touching the safety yoke.
When tool is not in use.
When moving to a different work area.
Such precautionary measures reduce the risk of injury to
persons.

LOADING TOOL

Do not load the tool with fasteners when any one of the
1.
operating controls is activated.
2. Never place a hand or any part of body in fastener
discharge area of tool.
Never point tool at anyone.
3.
4. Do not pull the trigger or depress the workpiece contact
as accidental actuation may occur, possibly causing
injury.
WARNING: The warnings and precautions discussed
above cannot cover all possible conditions and
situations that may occur It must be understood by
.
the user that common sense and caution are
factors which cannot be built into this product but
must be supplied by the user
.
6

Warranty

HUSKY PNEUMATIC NAILER KIT LIMITED TWO-YEAR WARRANTY
This warranty covers defects in workmanship or materials in this HUSKY pneumatic nailer kit for the two-year period from the
date of purchase. This warranty is specific to this pneumatic nailer kit. Warranties for other
This warranty applies only to the original retail purchaser and may not be transferred. This warranty does not cover normal
wear and tear or any malfunction, failure or defect resulting from misuse, abuse, neglect, alteration, modification or repair by
other than a service center authorized to repair
driver blades, seals, etc. are not covered by this warranty. This warranty does not apply to
application or for rental purposes. HUSKY
its pneumatic nailer kit other than those specifically stated in this warranty.

ADDITIONAL LIMITATIONS

,
To the extent permitted by applicable law, all implied warranties, including warranties of merchantability or fitness for a particular
purpose, are disclaimed. Any implied warranties, including warranties of merchantability or fitness for a particular purpose, that
can not be disclaimed under state law are limited to two years from the date of purchase. HUSKY is not responsible for direct,
indirect, incidental, special or consequential damages. If this
will apply for ninety (90) days from the date of purchase. Some states do not allow limitations on how long an implied warranty
lasts and/or do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations may not
apply to you. This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state.

Unpacking

1. This tool kit has been shipped completely assembled.
2.
Carefully remove the tool and any accessories from the
box.
3.
Inspect the tool carefully to make sure no breakage or
damage occurred during shipping.
Do not discard the packing material until you have
4.
carefully inspected and satisfactorily operated the tool.
5. If any parts are damaged or missing, please call
1-888-HD-HUSKY.
HUSKY
HUSKY branded air nailer. Expendable materials, such as O-rings, bumpers,
pneumatic nailer kit
makes no warranties, representations or promises as to the quality or performance of
pneumatic nailer kit is used for commercial purposes, the warranty
WARNING: If any parts are missing, do not operate the
tool until the missing parts are replaced. Failure to do
so could result in possible serious personal injury.
WARNING: Do not attempt to modify the tool or
create accessories not recommended for use with
the tool. Any such alteration or modification is
misuse and could result in hazardous condition
leading to possible serious personal injury.
7
Please contact 1-888-HD-HUSKY for further assistance.
products may vary.
used in industrial
HUSKYTOOLS.COM