Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Frame
Bumper
Rail
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 51183F
Wrenches: ¾", 7/8"
Drill Bits: ½"
Tape ½" flat washers to
Hitch as necessary to
Eliminate gap with frame
Figure 2
1
Qty. (4)
Carriage Bolt ½ x 1 ¼
2
Qty. (4)
Block ¼ x 1 ½ x 2"
3
Qty. (4)
Conical Toothed washer ½"
4
Qty. (4)
Hex nut ½"
1.
Detach (5) rubber exhaust hangers and lower rearward portion of exhaust system.
2.
Insert carriage bolts and blocks in frame rails thru access hole shown.
3.
Raise hitch into position and check side-to-side clearance with frame. Tape ½" washers to hitch as necessary to eliminate gap
(see figure 2).
4.
Raise hitch into position and attach with carriage bolts as shown in figure 1.
5.
Using hitch as a template, drill 2 holes in sides of frame rails.
6.
Insert hex bolt and lock washer thru side frame rail and secure with handle nut inserted thru end of frame rail.
7.
Reinstall exhaust system.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2009 Cequent Performance Products
Installation Instructions
BUICK LaCROSSE, BUICK ALLURE (CANADA ONLY),
BUICK CENTURY, OLDSMOBILE INTRIGUE
Drawbar Kit:
Fascia
Drawbar must be used in the
RISE position only
Access Hole
Use this slot for LaCrosse
And Allure models only
Tighten all ½-13 GR5 fasteners with torque wrench to 75 Lb.-Ft.
Do Not Exceed Lower of Towing Vehicle
36061
3500 LB (1589 Kg.) Max Gross Trailer Weight
Wiring Access Location: PC3, PC4
Frame Rail
Drill Holes
Use this slot for Century
And Intrigue models only
5
Qty. (2)
Hex bolt ½ x 1 ¼
6
Qty. (2)
Lock washer ½"
7
Qty. (4)
Flat washer ½"
8
Qty. (2)
Handle nut assembly
Sheet 1 of 3
51183N
Part Numbers:
Manufacturer's Rating or
300 LB (136 Kg.) Max Tongue Weight
½" flat washers as
Required for spacing
8-27-09
Form: F205 Rev A 5-6-05
51183
Figure 1
Rev. A
Publicidad
Manuales relacionados para Cequent Performance Products 51183
Resumen de contenidos para Cequent Performance Products 51183
- Página 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 51183N 8-27-09 Rev. A 2009 Cequent Performance Products Form: F205 Rev A 5-6-05...
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 2 de 3 51183N 8-27-09 Rév. A 2009 Cequent Performance Products Form: F205 Rev A 5-6-05...
- Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York. V.E.S.C. Regulación V-5 y SAE J684. Hoja 3 de 3 51183N 8-27-09 Rev. A 2009 Cequent Performance Products Form: F205 Rev A 5-6-05...