Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Hitch Shown In Proper Position
Equipment Required: Pull Wire (Provided), Pliers
Fastener Kit: 51143F
Wrenches: ¾", 15/16"
Drill Bits: None
8
Fishwire carriage bolt and
Block thru end of impact
Bar (one from each end
Of impact bar).
1
Qty. (2)
Carriage Bolt ½-13 x 1-3/4 GR5
2
Qty. (2)
Spacer Block ¼ x 1 x 3
3
Qty. (2)
Conical Toothed Washer – ½"
4
Qty. (2)
Hex Nut ½-13
1.
Lower vehicle spare tire (if required).
2.
Squeeze tabs that hold center portion of plastic step tread to impact bar with pliers (4 places – 2 on each end) and lift step tread.
3.
Raise hitch into position.
4.
Install 5/8" carriage bolts down thru holes between bumper and impact bat. Install lock washer and nut (hand tighten only until all fasteners are
installed).
5.
Fishwire ½" carriage bolts and ¼ x 1 x 3 spacer blocks thru end of impact bar and into holes in bottom surface of impact bar. Install conical
toothed washers and nuts.
Tighten all ½-13 GR5 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)
Tighten all 5/8-11 GR5 fasteners with torque wrench to 150 Lb.-Ft. (203 N*M)
Note: Tightening will cause 5/8" carriage bolt to draw down into impact bar holes. Carriage bolt must be completely seated to impact bar.
6.
Raise spare tire (if required).
7.
Tap lightly on plastic step tread to secure to bumper.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent
entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a
vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and
SAE J684.
z
2009 Cequent Performance Products
Installation Instructions
Dodge Ram 1500 Pickup (Built after 11-1-02)
Dodge Ram 2500 Pickup
Vehicle
Bumper
Dodge Ram 3500 Pickup
Vehicle License Plate
1234
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location: PU3
Plastic Step Tread
567
5
Qty. (2)
Carriage Bolt 5/8-11 x 2" GR5
6
Qty. (2)
Lock Washer – 5/8"
7
Qty. (2)
Hex Nut 5/8-11
8
Qty. (2)
Pull Wire – ½"
Sheet 1 of 3
51143N
Part Numbers:
51143
Max Gross
Max Tongue
Trailer WT (LB)
WT (LB)
8000 (3632 Kg.)
800 (363 Kg.)
5000 (2270 Kg.)
500 (227 Kg.)
Bumper
Vehicle Impact Bar
8-3-09
Form: F205 Rev A 5-6-05
Rev. A
Publicidad
Manuales relacionados para Cequent Performance Products 51143
Resumen de contenidos para Cequent Performance Products 51143
- Página 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 51143N 8-3-09 Rev. A 2009 Cequent Performance Products Form: F205 Rev A 5-6-05...
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 2 de 3 51143N 8-3-09 Rev. A 2009 Cequent Performance Products Form: F205 Rev A 5-6-05...
- Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. Hoja 3 de 3 51143N 8-3-09 Rev. A 2009 Cequent Performance Products Form: F205 Rev A 5-6-05...