Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Hitch Shown In Proper Position
Equipment Required: Tape
Fastener Kit: 51138F
Wrenches: 1-1/8", 22mm
Drill Bits: None
Frame Rail
Existing fasteners
Removed in Step 1
Reinstalled with
Additional washers
In Step 4.
4
Fasteners Typical
Both Sides
1
Qty. (1)
Hex Bolt ¾-10 x 2.75 GR5
2
Qty. (6)
Flat Washer ¾"
1.
Remove the lower bolts from the frame mounting brackets, (2) per side. Bolts will be use for hitch installation. Do not discard.
2.
Attach flat washers with tape to the underside of the bumper (see Figure 2).
3.
Insert bumper bracket mounting structure between flat washers (installed in Step 2) and bumper.
4.
Swivel hitch into position and loosely reinstall fasteners removed in Step 1 with additional flat washers.
5.
Install bumper bracket mounting structure fasteners as shown above.
6.
Tighten all fasteners to the required torque specifications
Tighten all ¾-10 GR5 fasteners with a torque wrench to 260 Lb.-Ft. (353 N*M)
Tighten all M14 CL8.8 fasteners with a torque wrench to 89 Lb.-Ft. (121 N*M)
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent
entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a
vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and
SAE J684.
z
2009 Cequent Performance Products
Installation Instructions
Dodge Dakota
Bumper
Weight Distributing
Weight Carrying
Wiring Access Location: PU1, PU2
Frame Mounting Brackets
1
2
Qty. 5 or 6
3
Bumper Bracket
Mounting Structure
Figure 1
3
4
Sheet 1 of 3
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
Max Gross
Hitch type
Trailer WT (LB)
8000 (3632 Kg.)
5000 (2270 Kg.)
Ball Mount
Qty. (1)
Lock Nut ¾-10 (w/Nylon Insert)
Qty. (8)
Flat Washer ½"
51138N
Part Numbers:
51138
Max Tongue
WT (LB)
800 (363 Kg.)
500 (227 Kg.)
Existing Weldnuts
Bumper
Bumper
Figure 2
Note: Additional flat washer
(provided) may be inserted
For more clearance.
8-11-09
Rev. A
Form: F205 Rev A 5-6-05
Publicidad
Manuales relacionados para Cequent Performance Products 51138
Resumen de contenidos para Cequent Performance Products 51138
- Página 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. 2009 Cequent Performance Products Sheet 1 of 3 51138N 8-11-09 Rev.
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. 2009 Cequent Performance Products Feuille 2 de 3...
- Página 3 Observe las precauciones de seguridad al trabajar por debajo del vehículo y use protección visual. No corte los orificios de acceso o accesorios con soplete. Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. 2009 Cequent Performance Products Hoja 3 de 3 51138N 8-11-09 Rev.