Publicidad
1.1 The vehicle to be lifted should never exceded the rated capacity of the Jack.
1.2 The maximum stroke of the Jack indicated on the label should never be exceeded.
1.3 The Jack should be supported on a solid, level and horizontal surface which is illuminated and free of abstructions Never stand the Jack on asurface which may
sink.
1.4 Ensure that there are no persons inside the vehicle to be lifted. Switch off the engine and apply the brake. Ensure The vehicle or element to be lifted against any
type of sliding. Use chooks if appropriate. Do not enter the vehicle or Stara
the engine whilst is supported on the jack appropriate stands. The jacks is a lifting decive only and should never be
used to move the vehicle.
1.5 Position the jack Ander the manufacture´s recommended lifting point for thr vrhicle and ensure that it is not corroded,
dirty or greasy. This point should remain centred over the jack saddle. All off-centred loads can slip and accidents may result.
1.6 During raising and lowering of the load, all precautions should be taken to avoid movement of the vehicle load. Traffic may cause the raised vehicle to rock during
roadside use of the jack.
1.7 The Jack should be positioned so as to avoid the need for the user to introduce any part of his/her body undeneath the vehicle. Never work Ander a raised vehicle
without previously supporting with mechanical stands or other appropriate methods. Never positon any part of your body near the movible elements of the jack.
1.8 It is necessary for the operador to be able to observe the lifting device and load during all movements in the presence of
movement of the vehicle, etc, the lifting process must prior be interrupted.
1.9 Ensure that there are no persons or obstructions underneath the vehicle prior to lowering.
1. 10 As an additional safety measure againts overload, the jack is fitted with an averload valve seta t the factory and which
should not be ajusted Ander any circumstances. If nominal capacity of the jack is exceded the overload valve Hill stop
1.1 Prior to operating the Jack remove any accumulated air from the system as follows: -insert the andel into the socket and
fix it with the screw provide.
-Pull the andel and turn it clockwise and, whilst held in this position. Puma the Jack several times ensure internal lubrication
and bleed the accumulated air from the system.
1.2 Release the andel and it Hill automatically return back to the initial position ("Dead man principle"). The Jack is now readyto be used.
Important: prior to lifting the load, ensure that all of the aforementioned safety instructions are followed.
1.3 The Wheel of the Jacks Should a always totale freely
1.4 These Jacks are fitted witha foot pedal that give a master apprach to the load.
1.5 For litting move the andel up and down using the full stroke range of the piston for greater speed. Seccure the lifted load as an esseantial safety measure with an
appropriate axie stand .
1.6 Before lowering lift the vehicle to remove the axle stands, ensuring that there are no persons or obstacles Ander the vicle to be lowered. Pull the andel and turn it
clockwise.
1.7 Our Jacks are fitted with a safety device LCS that funtions automatically and offers smooth and uniform lowering.
1.8 Once the vehicle has been lowered release the andel and it Hill automatically return back to the initial position.
Important: Both the maintenance and repair of the jack may only be performed by qualified persons, who have sufficient knowledge of the hydraulic systems used in these
decives as a result of their training and experience.
3.1 Keep the jack clean and lubricate all moving parts at regular intervals, which must be clean and protected from agressive conditions at all times.
3.2 Only original spare parts Should be Used.
3.3 Prior to each use, check for bent, broken, cracked or loose parts and solve the problem , if appropriate if it is suspected that the jack has been subjected to abnormal
loads or has suffered any knocks, withdraw it from service until the problem has been rectified.
3.4 if the oil level needs to bechecked or refilled, with the piston fully retracted, remove the filler plug and drain its contents into a container. With the jack in a horizontal
position, proceed to introduce the necessary volume as indicated for each model in these instructions. The parts table alongside shows the volume of oil required.
Make sure that no dirl enters with the new oil. Following a period of prolongad intensive use, it is recomendable to change the oil in order to extend the useful life of
the jack.
Important: An exceso of oil to the volume requierd mayrender the jack inoperative.
3.5 Only use hydraulic oil, type HL or Hm with an ISO grade of cinematic viscosity of 30 cST at 40s, ora n Engler viscosity of 3 at 50sC. Extreme imortant: Never use
Brake Fluid.
3.6 When the jack is not use, make sure the lifting arm is fully retracted to avoid corrosion. Apply an anti-corrosion to the pistons, if aprópiate.
3.7 Keep the jack in a clean, dry place and out of children reach.
3.8 At the end of the useful life of the jack, drain off the oil and hand it over toa n authorised agent and dispose of the jack in accordance with local regulations.
3.9 Both the repair kit, which exclusively contains the o-rings and seals of the jack, and the spare part sets must be ordered using the referente assigned in the table.
SAFETY INSTRUCTIONS
USE AND OPERATION
MAINTENANCE
dangerous conditions, such as
the lifting operation.
Publicidad
