Storage - Bona Belt UX Manual De Funcionamiento Y Mantenimiento

Operator Safety (Cont.)
Sanding may create an explosive environment. Cigarettes,
cigars, pipes, lighters, pilot flames, or any other source of fire
may create an explosion, if lit during sanding operations. All
sources of ignition should be removed entirely from the work
area.
Poorly ventilated work areas may create an explosive
environment, when some combustible materials (solvents,
thinners, alcohol, fuel, some paints, wood dust, etc) are
present in the atmosphere. Floor sanding may cause various
materials and fumes to ignite. Read the manufacturer's
instructions for each chemical product used and establish its
combustibility. Always keep the work area well-ventilated.
Striking nails when sanding may generate an explosion or fire.
Always ensure all nails are sunk before sanding surfaces.
Serious injury and/or death due to electrocution may occur, if
the power supply circuit trips repeatedly or is undersized. Have
the fuses, safety circuit and power supply line checked by an
authorized electrician.
Performing maintenance and/or repairing the machine, when
it is not fully disconnected from the power supply, may cause
serious injury and/or death due to electrocution. Disconnect
the power supply before carrying out any maintenance and/or
repair work.
The use of this machine on a circuit which is not grounded
may cause serious injury and/or death due to electrocution.
Never disconnect or disable the grounding conductor. Consult
an electrician, if the ground conductor is missing or it is
suspected that the circuit is not suitably grounded.
The use of this machine with a damaged power supply cable
may cause electric shock. Check the power supply cable
regularly for damage, such as splitting or wear and tear. DO
NOT use the machine, if the power supply cable is damaged.
DO NOT use the electric cable to move the machine. DO NOT
close a door on cord. DO NOT pull cord around sharp edges
or corners.
6
Bona Belt UX Manual
DO NOT unplug by pulling on power supply cable. To unplug
grasp the plug. DO NOT handle plug or operate machine with
wet hands. DO NOT put any objects into motor openings.
Serious injury and/or death due to electrocution may occur if
the machine runs over the power supply cable and it becomes
damaged. Keep the cable away from the sanding tool. Always
keep the power supply cable raised above the machine and
sand away from the power supply cable.
The moving parts on this machine may cause serious injury
and/or damage. Keep hands, feet and loose clothing away
from all moving parts of the machine.
Operating the machine without all guards, doors, or covers in
place can cause an injury or damage.
DO NOT pass with the machine on objects that are hot,
burning or smoking, such as cigarettes, matches or cinders.
Performing maintenance or replacing the dust bag may cause
injury to the operator or people nearby, if the machine is
connected to the power supply. Always unplug the machine
when not in use.
DO NOT use solvents or other flammable products to clean
this machine.
Dry use only. DO NOT use for liquid recovery, which could
result in motor failure, electric shock, and electrocution.
Operator Safety (Cont.)
Never become distracted during sanding operations, check
what is happening continually. Use common
sense. DO NOT use the machine, if you are tired, have
consumed alcohol or have taken medication that
may affect your judgement or your body control.
DO NOT smoke during sanding operation.

Storage

It is advisable to store the machine in its original
packaging. Doing so makes it possible to form a
column of two packages maximum, with one
on top of the other.
If the machine is removed from the original
packaging and is not used for some time ensure
the wheels and drum are not in contact
with the ground.
Bona Belt UX Manual
DO NOT use this machine to sand steps and furniture.
DO NOT ride on this machine.
DO NOT put any objects into openings. DO NOT use with
blocked openings. Keep free from dust, lint, hair or anything
that may reduce airflow.
This equipment is for dry use only and must not be used
or kept outside in wet conditions. Store the machine in a
dry building, otherwise the machine could be damaged.
Storage temperature
from -20 °C to 50 °C.
EN
7