Storage; Transporting And Handling - Bona Edge UX Manual De Funcionamiento Y Mantenimiento

Operator Safety (Cont.)
Sanding may create an explosive environment. Cigarettes,
cigars, pipes, lighters, pilot flames, or any other source of fire
may create an explosion, if lit during sanding operations. All
sources of ignition should be removed entirely from the work
area.
Poorly ventilated work areas may create an explosive
environment, when some combustible materials (solvents,
thinners, alcohol, fuel, some paints, wood dust, etc) are present
in the atmosphere. Floor sanding may cause various materials
and fumes to ignite. Read the manufacturer's instructions for
each chemical product used and establish its combustibility.
Always keep the work area well-ventilated.
Striking nails when sanding may generate an explosion or fire.
Always ensure all nails are sunk before sanding surfaces.
Serious injury and/or death due to electrocution may occur, if
the power supply circuit trips repeatedly or is undersized. Have
the fuses, safety circuit and power supply line checked by an
authorized electrician.
Performing maintenance and/or repairing the machine, when
it is not fully disconnected from the power supply, may cause
serious injury and/or death due to electrocution. Disconnect
the power supply before carrying out any maintenance and/or
repair work.
The use of this machine on a circuit which is not grounded may
cause serious injury and/or death due to electrocution. Never
disconnect or disable the grounding conductor. Consult an
electrician, if the ground conductor is missing or it is suspected
that the circuit is not suitably grounded.
The use of this machine with a damaged power supply cable
may cause electric shock. Check the power supply cable
regularly for damage, such as splitting or wear and tear. DO
NOT use the machine, if the power supply cable is damaged.
DO NOT use the electric cable to move the machine. DO NOT
close a door on cord. DO NOT pull cord around sharp edges or
corners.
6
Bona Edge UX
DO NOT unplug by pulling on power supply cable. To unplug
grasp the plug. DO NOT handle plug or operate machine with
wet hands. DO NOT put any objects into motor openings.
Serious injury and/or death due to electrocution may occur if
the machine runs over the power supply cable and it becomes
damaged. Keep the cable away from the sanding tool. Always
keep the power supply cable raised above the machine and
sand away from the power supply cable.
The moving parts on this machine may cause serious injury
and/or damage. Keep hands, feet and loose clothing away from
all moving parts of the machine.
Operating the machine without all guards, doors, or covers in
place can cause an injury or damage.
DO NOT pass with the machine on objects that are hot, burning
or smoking, such as cigarettes, matches or cinders.
Performing maintenance or replacing the dust bag may cause
injury to the operator or people nearby, if the machine is
connected to the power supply. Always unplug the machine
when not in use.
DO NOT use solvents or other flammable products to clean this
machine.
Dry use only. DO NOT use for liquid recovery, which could result
in motor failure, electric shock,
and/or electrocution.
Operator Safety (Cont.)
Never become distracted during sanding operations, check
what is happening continually. Use common sense. DO NOT
use the machine, if you are tired, have consumed alcohol or
have taken medication that may affect your judgement or your
body control.
DO NOT smoke during sanding operation.

Storage

It is advisable to store the machine in its original packaging.
Doing so makes it possible to form a column of three packages
maximum, with one on top of the other.
If the machine is removed from the original packaging and is
not used for some time ensure the wheels and disc are not in
contact with the ground.

Transporting and Handling

1) Ensure the power supply cable is disconnected from the mains.
2) Always move the sanding machine using two handles with the bag support turned upwards. Protect the sanding disc with an
abrasive disc and ensure the screws fastening the abrasive disc are secured well. When transporting the sanding machine on
a vehicle always ensure it is well secured and cannot move.
Bona Edge UX
DO NOT use this machine to sand furniture.
DO NOT put any objects into openings. DO NOT use with
blocked openings. Keep free from dust, lint, hair or anything
that may reduce airflow.
DO NOT clean the machine using a high pressure washer or
hose.
This equipment is for dry use only and must not be used or
kept outside in wet conditions. Store the machine in a dry
building, otherwise the machine could be damaged.
Storage temperature from -20°C to 50°C.
EN
7