Publicidad
Idiomas disponibles
Idiomas disponibles
VEHICLE FRAME
HOLE 1
NISSAN PICK-UPS
USE THIS BRACKET
LOCATION
USE THIS HOLE
FOR CENTER
SECTION ASSEMBLY
NOTE:
General assembly - loosely assemble center section (page 1);
loosely install side brackets on vehicle (this page);
install center section assembly (page 2-3);
tighten all fasteners to proper specifications (page 1).
1983-2004 CHEVROLET S-10/GMC SONOMA - LONG BED 2 & 4WD / 1987-04 NISSAN PICK-UP & FRONTIER W/56" BEDS
1. Center the side brackets on frame and align hole 2 under large hole (if present) near end of frame.
(Note: Some models require 1/2" spacers between side bracket and frame.)
2. Insert 1/2" carriage bolts with 1/4 x 1-1/2 x 3" bolt plates down through large hole in frame and into hole 2 in
side bracket. Use 1/2" spacers if necessary.
3. Install 1/2" flat washers, lock washers, and nuts on the carriage bolts.
4. Using hole 4 in bracket as a guide, drill a 1/2" hole into the frame at hole 4.
5. Install 1/2" carriage bolts with 1/4" bolt plates through drilled hole.
6. Install 1/2" flat washers, lock washers, and nuts on the carriage bolts.
7. Install center section per SIDE BRACKET LOCATION 1 - LOCATION 2 for Nissan pick-ups. (See page 2.)
**If large hole is not present near end of frame:
8. Raise side brackets in approximate position shown and clamp in place. Using holes in side bracket as a guide,
drill 1/2" holes into frame at holes 2 & 4.
9. See steps 5 through 7 to finish installation.
1982-1993 DODGE RAMCHARGER
1. Position the side brackets up to the frame with hole 1 under the rivet head. Clamp in place or mark the frame at holes 2 and 4. Drill a
1/2" hole into the frame at holes 2 and 4.
2. Place a 1/2" thick spacer between the frame and holes 2 and 4. Thread a 1/2" carriage bolt onto the pull wire. Place a bolt plate over
the bolt. Push the free end of the pull wire through the end of the frame and bring it out through the 1/2" mounting hole. Pull the bolt
down through the hole. Unscrew the pull wire and repeat for the other bolts.
3. Install 1/2" flat washers, lock washers, and nuts on the bolts.
4. Install center section per SIDE BRACKET LOCATION 1. (See page 2.)
1982-03 FORD FULL SIZE PICK-UP/ 2004 F250/F350 AND F150 HERITAGE ONLY
1. Position hole 2 of side brackets just rearward of the rivet in the frame. Place a 1/2" thick spacer between the frame and
holes 2 & 4. Clamp the side brackets in place. Drill a 1/2" hole into the frame using holes 2 & 4 as a guide. If rivet is at hole 4, then
use hole 3.
Insert 1/2" carriage bolts with 1/4" bolt plates down through the frame and into holes 2 & 4. Install 1/2" flat washers,
lock washers, and nuts on all bolts.
2. Install center section per SIDE BRACKET LOCATION 1. (See page 2.)
REFER TO SIDE BRACKET LOCATION INSTRUCTIONS FOR PROPER BOLT TIGHTENING SEQUENCE
INSTALLATION C
DRILLED HOLE
DRILLED HOLE (ON SOME MODELS)
EXISTING LARGE HOLE (ON SOME MODELS)
1/2" THICK SPACER
WHEN NEEDED
1/4" BOLT PLATE
(If the 1-1/8" dia. hole is present,
then use the 1/4 x 1-1/2 x 3 Block
for this attachment.)
S-10/SONOMA PICK-UPS
& DODGE RAM CHARGER
USETHIS BRACKET
LOCATION
TOOLS REQUIRED
3/4" SOCKET
1/2" DRILL
TORQUE WRENCH
SAFETY GLASSES
1/2 x 2"
CARRIAGE BOLTS
HOLE 4
HOLE 3
HOLE 2
1/2" FLAT WASHER
1/2" LOCK WASHER
1/2" HEX NUT
8
Publicidad
