Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
BEFORE CALLING
FOR SERVICE (continued)
Your washing machine is equipped
with an automatic
error-monitoring
system to detect and diagnose problems at an
early stage.
Water in the washer
drains slowly
or not at
all, or the display
shows:
|
,_,c|
Washer tills with water
slowly or not at all, or
the display shows:
Drain hose is kinked,
pinched,
or clogged.
The drain pump filter
is clogged.
Drain discharge
is more than 96 inches
above
bottom
of washer.
Water
supply faucets are not open fully.
Water
line hoses are kinked,
pinched,
or
crushed.
Water
inlet filters are clogged.
Water
supply
pressure to faucet
or house is
too low.
! i
! !! !!! !i ! !! !! !! !! !i ii i!! i! ! !!!!!!i!i!iiiiiiiiiiiii
Make
sure the drain
hose is free of clogs, kinks,
etc., and is not pinched
behind
or under the
washer.
Clean the drain pump filter.
See Maintenance
in
the Care and Cleaning
section.
Adjust
or repair
drain.
Maximum
drain
height is
96 inches.
Make
sure that the water
faucets
are fully open.
Make
sure the hoses are not kinked or pinched.
Be careful
when moving
the washer
during
cleaning
and maintenance
Clean the inlet filters.
See Maintenance
in the
Care and Cleaning
section.
Check another
faucet
in the house to make
sure
that
household
water
pressure is adequate
and
flow is not restricted.
Water
supply
connected
with leak-limiting
Hoses designed
to limit leaks can trip falsely
hoses,
and prevent
the washer from filling.
The use of
leak limiting
hoses is not recommended.
Cycle won't
start, or the
The door is not closed
properly.
Make
sure that the door is closed properly
and
display
shows:
press the START/PAUSE
button.
After
starting
I
!
a cycle, it may take a few moments
before
the
d
n=n _
drum begins to turn or spin. The washer will not
or
operate
unless the door is locked.
I
I- -_!
If the door is closed
and locked
and the open
f_l
I_1_
m
door error message
is displayed,
call
for service.
The display
shows:
Load is too small.
Add 1 or 2 similar items to help balance the load.
I
_ II- i
Load is out of balance.
The washer has an imbalance
detection
and
UL- _
correction
system. If individual heavy articles are
loaded
(bath mat, bath robe, etc.) and the imbal-
ance is too great, the washer will make several
attempts to restart the spin cycle. If an imbalance
is still detected,
the washer will stop and the error
code will display.
The display
shows:
Control
error.
Unplug the washer and wait 60 seconds. Reconnect
j j- _
power and try again. If the error reappears,
call for
L- L- _
service.
The display
shows:
Water
level is too high due to a faulty
Close the water faucets, unplug the washer, and
I
l-l_-
'-'-I
water
valve,
call for service.
The display
shows:
The water level sensor is not working
Close the water
faucets, unplug the washer, and
m
OF
r-el
he displa_
n_c|
The display
shows:
shows:
correctly.
A motor
error has occurred.
A power
failure
has occurred.
call for service.
Allow
the washer
to stand for 30 minutes
and
then restart the cycle.
If the LE error code per-
sists, call for service.
If the power
to the washer
has been interrupted
during
a cycle, the PF error code will display
the next time the washer
is turned
ON.
This will
alert you to the fact that the previous
cycle may
not have been completed.
Select any cycle to
clear the error code and use the washer.
3O
Publicidad
Tabla de contenido
