DeWalt DWE4222N Instalación

ENGLISH
Lanyard Attachment Point Installation
To be used with DWE4222N, DWE43066N,
DWE43114N, DWE43115N, DWE43144N, DWE46144N,
DWE46166N Grinders

WARNING: The lanyard attachment point
only be added to certain models and must be installed
by an authorized service center.

WARNING: For your own safety, read the grinder
instruction manual before using any accessory. Failure
to heed these warnings may result in personal injury
and serious damage to the vacuum and the accessory.

WARNING: Retain this document with the tool
instruction manual for future reference.
Lanyard Attachment Point (Fig. B)
Safety Warnings Specific for Use At Height
• If the tool is dropped for any reason, the lanyard
attachment point 1
serviced prior to re-use. The lanyard attachment point
is designed to stretch to absorb the shock of a drop. Any
permanent stretch to the device exposing the red marked
internal coils indicates it has been compromised and must
be serviced prior to reuse.
• Always keep the tool and accessories tethered when
working "at height". (Maximum lanyard length: 6.5 ft
[2 m])
• Use only with lanyards appropriate for this tool type and
rated for at least 6 lbs (2.72 Kg).
Crush, cut or entanglement hazard. Do not use near
•
moving parts, mechanisms or running machinery.
• Do not anchor the tool lanyard to anything on your body.
Anchor to a rigid structure that can withstand the forces
of a dropped tool.
• Make sure the lanyard is properly secure at each end prior
to use.
• Inspect tool and lanyard before each use for damage and
proper function (including fabric and stitching). Do not
use if damaged or not functioning properly.
• Do not alter the lanyard attachment point or use in a
manner other than as instructed in this manual.
• Only attach tool to a lanyard with a locking carabiner. Do
not attach by looping or knotting the lanyard. Do not use
rope or cord.
• Electrical shock hazard. Be sure power is off when working
in high voltage areas. Some lanyards are conductive.
• Dropped tools will swing on the lanyard, which could
cause injury or loss of balance.
• Do not carry the tool by lanyard attachment point or
the lanyard.
• Do not attach more than one tool to each lanyard.
final page size: 8.5 x 5.5 inches
1 may
must be inspected and properly
• Only use appropriate D WALT brand lanyard attachment
e
point. NEVER modify tools to create attachment points.
• Only transfer the tool between hands while properly
balanced in a stable orientation.
• Do not attach lanyards to tool in a way that keeps guards,
switches or lock-offs from operating properly.
• Avoid getting tangled in the lanyard.
• Keep lanyard away from the cutting area of the tool.
• Do not use lanyards or attachment devices to get
additional leverage from the tool.
• Do not use for personal fall protection.
• Falling object hazard! Only change accessories and
attachments where a dropped object won't cause
a hazard below you. Consult your Authority Having
Jurisdication (AHJ) or site supervisor for procedures for
working at height.
• Use multi-action and screw gate type carabiners. Do not
use single action spring clip carabiners.
The lanyard attachment point
competent personnel, who are trained and knowledgeable
regarding working with tools in and around machinery and
"at height".
Installation
DWE43115N, DWE43066N, DWE46166N (Fig. A, B)
1. Position the loops of the lanyard attachment point on
each side of the tool housing.
2. Slide provided bolt through first washer, both loops and
the housing. Install second washer and nut onto bolt
and tighten securely.
IMPORTANT: Always use manual, torque-calibrated
screwdrivers and tighten to
15.9–18.6 in lbs (1.8–2.1 Nm). Do not use pneumatic or
electric screwdrivers.
DWE4222N, DWE43114N, DWE43144N, DWE46144N
(Fig. C, D)
1. Slide the metal bars of the lanyard attachment point
1 into the slots at the rear of the tool housing, making
note which has the threads.
2. Insert the screw into the housing side without the
threaded bar and feed it through until it engages the
threads of the other bar. Tighten the screw securely.
IMPORTANT: Always use manual, torque-calibrated
screwdrivers and tighten to 15.9–18.6 in lbs (1.8–
2.1 Nm). Do not use pneumatic or electric screwdrivers.
For more information, please contact D
address below or 1-800-4-D
e
FRANCAIS
Installation du point de fixation des
longes
À utiliser avec les meuleuses DWE4222N,
DWE43066N, DWE43114N, DWE43115N, DWE43144N,
DWE46144N, DWE46166N

AVERTISSEMENT: le point de fixation des longes
de sécurité 1 peut seulement être ajouté à certains
modèles et doit être installé par un centre de services
autorisé.
1 is intended for use by
WALT at the
e
WALT (1-800-433-9258).