Replacing The Battery; Customer Service - Peg-Perego CORRAL T-REX Manual Del Usuario

PROBLEMS?
THE VEHICLE DOES NOT WORK?
• Check that there are no disconnected cables under
the accelerator plate.
• Check the operation of the accelerator button and
replace it if necessary.
• Check that the battery is connected to the
electrical system.
THE VEHICLE LACKS POWER?
• Charge the batteries. If after charging the problem
persists, have the battery and charger checked by
an assistance centre.

CUSTOMER SERVICE

PEG PEREGO offers an after-sales customer
service, directly or through a network of
authorized assistance centres, for any repairs or
replacements and the sale of original spare parts.
To contact a service center, visit our website:
http://global.pegperego.com/toys-
site/support/
The item's serial number must always be quoted.
See the page on spare parts to find out how to
identify the serial number.
ASSEMBLY INSTRUCTIONS
WARNING
ASSEMBLY MUST ONLY BE CARRIED OUT BY
ADULTS. TAKE CARE WHEN REMOVING THE
VEHICLE FROM ITS PACKAGING. ALL THE
SCREWS AND SMALL PARTS ARE CONTAINED IN
A BAG INSIDE THE PACKAGING. THE BATTERY
MAY ALREADY BE FITTED INSIDE THE ITEM.
Do not use the toy if you find it damaged after
opening the packaging. Contact the shop where you
bought it or the customer support centre.
Take care in the presence of children while
assembling the toy, given the risks caused by small
parts (ingestion hazard) and the plastic bags that
contain them (choking hazard).
To assemble the toy, you will need a flat-head
screwdriver, a Phillips screwdriver, a hammer, and a
pair of pliers.
ASSEMBLY
1 • Push the gear lever down into its housing until it
clicks into place.
2 • Position the bumper on the front of the frame.
Raise.
3 • Fit the bumper.
4 • Position and fix the dashboard.
5 • Slot the handlebars into their holder. Make sure
that the ribs on the handlebar section fit
perfectly into the grooves in the holder, as
shown in the figure.
6 • Fasten the newly assembled handlebar unit in
place with a screw.
7 • Insert the handlebar cap.
8 • Push the grips on all of the way to the end. Make
sure that the teeth connect properly.
9 • Slot the handlebar unit onto the steering column.
Push upwards to bring the 2 holes together, as
shown in the figure.
10 • Secure the unit with a screw.
11 • Fit the mudguard wing, making sure that you
completely insert first the 2 clips and then the
pin.
12 • Put the screw in the pin and screw on the wing.
Do the same for the other wing.
13 • Connect the exhaust pipe inserting the tab A in
the bodywork hole.
14 • Fix the exhaust pipe with the screw supplied. Do
the same for the other pipe.
15 • Slip the aerial into the special hole and press..
16 • Remove the steering lever protection caps.
17 • Press the 4 hubcaps into place on the external
part of the wheels.
18 • Insert 1 large washer, 1 front wheel equipped
with a cylindrical bushing, 1 small washer, and 1
nut onto the steering lever, in this order.
19 • Tighten with the key provided. Repeat these
operations for the other front wheel.
20 • Take the axle out of the packaging and remove
the protective caps. Insert the axle into the rear
part of the vehicle, as shown in the figure.
21 • Insert 1 wheel, 1 small washer, and 1 nut from
each side of the axle, in this order. Fasten the
wheels using the 2 keys provided to tighten the 2
nuts simultaneously, as shown in the figure.
22 • Push the 4 hub covers firmly on, making sure
that the tabs fit into the slots in the hubcaps.
23 • Figure A shows a locked saddle. Turn the red lock
behind the saddle and bring it to the position
shown in figure B to open it.
24 • Press on the rear of the bodywork to facilitate
opening the saddle. Open the saddle.
25 • Connect the plugs. When you have finished,
remember to close and fix down the saddle. The
vehicle is ready to use.
VEHICLE FEATURES AND
INSTRUCTIONS FOR USE
26 • PEDAL: Accelerator only, brake is automatic.
27 • GEAR LEVER: the vehicle has three gears: 2
forward and 1 reverse. Please note: when it is
removed from the packaging the vehicle only
travels in first gear and reverse. In order to be
able to use second gear follow the instructions in
the illustrations below.
1 = first gear
2 = second gear
R = reverse
28 • Remove the screw in the second gear lock.
29 • Turn the second gear lock as shown in the figure.
30 • Replace and tighten the screw in the second gear
lock.
31 • The gears are now all available. Move the lever
backwards to change into second gear.

REPLACING THE BATTERY

PLEASE NOTE: THE PICTURES OF THE BATTERIES
ARE FOR ILLUSTRATIVE PURPOSES ONLY. YOUR
BATTERY MAY BE DIFFERENT FROM THE MODEL
SHOWN. THIS DOES NOT AFFECT THE
REPLACEMENT AND CHARGING PROCEDURES
DESCRIBED.
32 • Rotate the red lock behind the saddle and open
it. Press on the rear of the bodywork to facilitate
opening the saddle. Unplug vehicle wiring
terminal from battery terminal, by pressing
terminals on side and pulling apart.
33 • Loosen the battery holder.
34 • Replace the battery. Put the battery holder back
in place, tightening the 2 screws; reconnect the
plugs, and close the saddle.
BATTERY RECHARGE
WARNING: BATTERY CHARGING AND EVERY
OTHER OPERATION ON THE ELECTRICAL
SYSTEM MUST BE CARRIED OUT BY ADULTS
ONLY. THE BATTERY CAN ALSO BE CHARGED
WITHOUT REMOVING IT FROM THE TOY.
35 • Unplug vehicle wiring terminal B from battery
terminal A, by pressing terminals on side and
pulling apart.
36 • Plug the battery charger terminal to a wall outlet
following the instructions enclosed. Connect the
plug B to the battery charger plug C.
37 • Once the charge is completed unplug recharger
from wall outlet. Unplug recharger cord terminal
C from battery terminal B.
38 • Plug battery terminal A into vehicle wiring
terminal B. Close saddle.