Introduction To Use - Femi 1050 3D Instrucciones Para El Uso Y Manutencion

INDEX
1 INTRODUCTION TO USE .........................................9
2 INSTALLATION ........................................................12
3 ADJUSTING .............................................................13
5 ACCESSORIES .......................................................14
6 MAINTENANCE .......................................................15
7 TROUBLESHOOTING .............................................16
Manual translated from the original
1

INTRODUCTION TO USE

WARNING: before using your mitre-saw, please
read this instruction manual very carefully in
order to become familiar with the machine and
its recommended use.
Do not lose this manual as it is an essential part of the
machine itself. We recommend you always refer to it in
order to operate the machine in the best and safest way
possible.
Keep the manual with the machine and handy at all times
so it can be consulted whenever necessary.
This machine is designed solely and exclusively for
the uses indicated below. Use in accordance with the
recommendations provided in this manual. NEVER tamper
with it, force it or use it for any purpose not envisaged in
these instructions.
The operator is adequately trained in the use, adjustment
and operation of the machine.
1.1 SAFETY INFORMATION AND NOTES
Pay particular attention to the indications "WARNING",
"CAUTION" and "NOTE" contained in this manual.
Symbols and notes precede all hazardous operations both
to give safety indications, to draw the users' attention to
danger and also to outline the appropriate behaviour to
adopt to avoid such events.
The three symbols used and relative wording are the
following:
WARNING: a hazardous situation/action which could
be severely harmful.
CAUTION: a situation/action which could be
moderately harmful or damage objects.
NOTE: the notes preceded by this symbol are of a
technical nature and simplify use.
Double insulation. This symbol means that you
cannot get at any element carrying the electrical
current without using a tool. Tools which have
this symbol do not have any earthing protection
systems.
Indicates that this machine is equipped with a laser
pointing device
1.2 TECHNICAL FEATURES
Power .................................................................. 1800 W
Voltage and frequency ..................................230V ~ 50Hz
Speed ...........................................................3600 rev/min
Saw blade maximum dimensions: ....... 305 x 3.2 x 30 mm
Crosscut at 90°:: ..........................................305 x 90 mm
Oblique cutting 45°, left and right: ................215 x 90 mm
Inclined cutting 45° left:: ...............................165 x 65 mm
Compound cut ...................................................................
(transversal and inclined 45° left): .................45 x 70 mm
Upper surface maximum blade projection: .............60 mm
Left and right stops: ..................... 0°-15°-22.5°-30°- 45°
Inclination stops: ................................................ 0 and 45°
Laser: ............................... (in accordance to EN60825-1:
.......................................1994+A1+A2 regulation) Class 2
Net weight:................................................................29 kg
Packaging measurements: .............. 990 × 650 × 460 mm
1.3 SAFETY AND RULES
The machine was designed and built according to the
Community Directives in force: EC/2006/42 - EC/2006/95
- EC/2004/108.
The enclosed CE Declaration of conformity, together with
the CE mark on the product itself are an integral part of
the machine: both guarantee product conformity with the
aforesaid safety Directives.
1.4 ENVISAGED USE AND UNFORESEEN USE
The most advanced technologies have been used to design
and manufacture the mitre-saw. It is suitable to cut wood,
aluminium and plastics and can be used by professionals,
craftsmen and expert hobbyists alike.
ENVISAGED USE
To cut:
- HARD AND SOFT, DOMESTIC AND EXOTIC WOOD
BOTH LONGITUDINALLY AND TRANSVERSALLY
and with appropriate adjustments (specific blade and
clamps only mitre-saw mode):
- PLASTICS
- ALUMINIUM AND ALUMINIUM ALLOYS
UNFORESEEN USE
Do not cut:
- MAGNESIUM
- FERROUS MATERIALS, STEEL AND CAST IRON OR
ANY OTHER MATERIAL NOT MENTIONED ABOVE
- IT IS STRICTLY FORBIDDEN TO USE THE SAW
TO CUT MATERIALS WHICH MAY, ON CUTTING,
RELEASE TOXIC SUBSTANCES.
- USE OF THE CIRCULAR SAW WITHOUT THE BLADE
GUARD IS STRICTLY PROHIBITED
- DO NOT FORCE THE MACHINE. YOU CAN OBTAIN
BETTER AND SAFER RESULTS IF YOU USE THE
MACHINE AT THE CUTTING PRESSURE FOR WHICH
IT HAS BEEN DESIGNED
- IT IS STRICTLY FORBIDDEN TO CUT DAMP WOOD
WITH THE SAW DURING WHEN OPERATING THE
SAW IN WORKBENCH MODE.
- USING HIGH SPEED BLADES IN STAINLESS STEEL
IS STRICTLY FORBIDDEN
- IT IS SEVERELY PROHIBITED TO USE THE MACHINE
FOR CARRYING OUT BLIND CUTS
9