Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
*P519-046*
P519-046
ALX170 and ND170 Single Dummy Lever
For ALX172 and ND172 Double Dummy Lever, see page 2.
Tools required
Pin wrench
(included)
Installation Preparation
Door preparation:
For door preparation use the template included in the package with the
lock. For additional information, visit the website www.allegion.com/us.
1
Install backplate (through-door bolt option ONLY).
1a
If using the through-door bolt kit, install the backplate
on the housing with two screws.
If not using the through-door bolt kit, skip
to step 2.
2
Install housing assembly.
For through-door
bolt kit only
Door
edge
ALX170, ND170
Optional Through-Door Bolt Kit
Part # 47262735
Washer
Backplate
mounting
screws (2)
Backplate
Lever catch
faces door
edge.
Bolt
Rose
3
For through-door bolt option ONLY, install bolt and
washer.
4
Install rose.
a
5
Install lever.
Firmly push on until lever catch engages.
Installation Instructions
Housing assembly
Mounting screws (2)
Align dimple
and groove.
Lever
catch
Lever
b
Rotate rose
until it stops.
Publicidad
Manuales relacionados para Schlage ALX170
Resumen de contenidos para Schlage ALX170
- Página 1 ALX170, ND170 *P519-046* P519-046 ALX170 and ND170 Single Dummy Lever Installation Instructions For ALX172 and ND172 Double Dummy Lever, see page 2. Optional Through-Door Bolt Kit Tools required Part # 47262735 Bolt Washer Backplate mounting screws (2) Housing assembly Pin wrench...
-
Página 2: Installation Preparation
ALX172, ND172 ALX172 and ND172 Double Dummy Lever Installation Instructions Tools required Optional Blank Latch Plate Kit Lever Blank latch Rose plate Mounting screws (2) Screws (2) Part # 47269199 Pin wrench (included) Inside Outside housing housing Lever Installation Preparation Rose Door preparation: For door preparation use the template included in the package with the... - Página 3 ALX170, ND170 ALX170 y ND170 Palanca única de simulación Instrucciones de instalación ALX170 et ND170 Faux levier simple Notice d’installation Para ALX172 y ND172 Palanca doble de simulación, véase la página 5. Pour ALX172 et ND172 Faux levier double, voir la page 5.
- Página 4 Instale el embellecedor. Instale la manija. Installer la rosette. Installer le levier. Presione firmemente hasta que entre la traba de la manija. Alinee el Rotar hasta que se hoyuelo y el detenga la rosa. Poussez fermement jusqu’à ce que le loquet du levier surco.
- Página 5 ALX172, ND172 ALX172 y ND172 Palanca Doble de Simulación Instrucciones de instalación ALX172 y ND172 Faux Levier Double Notice d’installation Herramientas Kit Opcional de Placa de Cierre en Manija necesarias Blanco Levier Outils Trousse de Plaque de Loquet Vierge Embellecedor nécessaires Facultative Rosette...
- Página 6 Si la utiliza, instale la placa de cierre en blanco Instale el embellecedor exterior. opcional. Installer la rosette extérieure. Installez la plaque de loquet vierge facultative, le cas échéant. Rotar hasta que se detenga Alinee el la rosa. hoyuelo y el surco.
- Página 7 © Allegion 2019 Printed in U.S.A. P519-046 Rev. 08/19-b...