Environmental Protection - Lista CBE250L Traducción De Las Instrucciones Originales

line. (See Fig. N)
2. LINE FEEDING
Your trimmer uses 1.4mm diameter, round nylon
line to cut grass and weeds quickly and easily.
During use, the tip of the nylon line will get
shorter due to wear. Gently bump the unit on the
ground and the line will feed out (See Fig. O).
Cutting line will wear faster and require more
feeding if the cutting or edging is done along
sidewalks or other abrasive surfaces or heavier
weeds are being cut.
3. CLEARING JAMS AND TANGLED LINES
From time to time, especially when cutting thick
or stalk weeds, the line feeding spool head may
become clogged with sap or other material and
the line will become jammed as a result. To clear
the jam, follow the steps listed below.
1) Unplug the trimmer.
2) Press the release tabs on the spool head, as
shown in Fig. P and remove the spool head by
pulling it straight off.
3) Remove the spool of nylon line out of the spool
head and clear any broken line or cutting debris
from the spool area. (If you plan to replace the
spool, this is the place to do so, otherwise, move
on.) (See Fig. Q)
4) Unwrap about one foot (30cm) of line to
ensure that it's undamaged. If it is OK rewind it
and insert the line end through the eyelet in the
spool head as show in Fig. R, Insert the other line
through the other eyelet. Ensure the springs are
in place under the spool. Pull the line through the
hole to maintain tension while placing the spool
down into the spool head as show in Fig R.
5) Press the spool down GENTLY until you feel it
drop into place. Take care to keep the lines from
becoming trapped under the spool.
6) Snap the spool head cover back on and at
the same time pull lines and be sure that they
are released from spool rail notches. If not, the
function of bumping- feed can not operate. Hold
the tool in the trimming position and turn the tool
on. In few sends or less, you'll hear the nylon
line being cut to proper length. If not, bump the
feed head gently on the ground to initiate a fresh
length of line.
4. SPOOL OR LINE REPLACEMENT
(USE 1.4mm DIAMETER ROUND LINE ONLY)
1) Reform steps 3.1 and 3.2 above.
2) Remove the spool from the spool head,
remove the line wrap ring(a) from the spool and
discard all line on the spool.(see Fig. R)
3) WARNING! Use only 1.4mm cutting
line, diameter line. Other sizes of line
will not feed properly and will result in improper
cutting head function or can cause serious injury.
Take approximately 5m of line into the spool
holes and wind line in the direction of the arrows
on the top of the spool.
Care should be taken to ensure that the line is
neatly coiled on the spool. Failure to do so will
impair the efficiency of the automatic line feed.
(See Fig. S)
Then fit the line wrap ring onto the spool and
snap the spool onto the spool head.
NOTE: Snugly and evenly wind the bulk line
onto the spool in the direction of the arrow on the
spool until the line builds up to the notches in the
spool rim. Do not overfill spool. The spool holds
about 5m of line (see Fig. T).
MAINTENANCE
Remove the plug from the socket before
carrying out any adjustment, servicing or
maintenance.
Your power tool requires no additional lubrication
or maintenance. There are no user serviceable
parts in your power tool. Never use water or
chemical cleaners to clean your power tool. Wipe
clean with a dry cloth. Always store your power
tool in a dry place. Keep the motor ventilation
slots clean. Keep all working controls free of
dust. Occasionally you may see sparks through
the ventilation slots. This is normal and will not
damage your power tool.
If the supply cord is damaged, it must be
replaced by the manufacturer, its service agent
or similarly qualified persons in order to avoid a
hazard.
ENVIRONMENTAL
PROTECTION
Waste electrical products should not
be disposed of with household waste.
Please recycle where facilities exist.
Check with your Local Authority or retailer for
recycling advice.
27