Chapin 2014 Manual De Instrucciones

WARNING
WARNING: Improper use or failure to follow instructions can result in explosive failure causing
serious eye or other injury. For safe use of this product you must read and follow all instructions. Do not
leave a pressurized sprayer in the hot sun. Heat can cause pressure build-up resulting in possible explosion.
Do not store or leave solution in tank after use. Always wear goggles, gloves, long sleeve shirt, long pants
and full foot protection when spraying. Never use any tool to remove pump if there is pressure in sprayer.
Never stand with face or body over top of tank when pumping or loosening pump to prevent ejecting pump
assembly and/or solution from striking and injuring you. Never pressurize sprayer by any means other than
the original pump. Do not attempt to modify this sprayer. Replace parts only with manufacturer's original
parts. Never spray flammable, caustic, acidic, chlorine, bleach or other corrosive solutions or heat,
pressure, or gas producing chemicals. Always read and follow chemical manufacturer's instructions
before use with this sprayer as some chemicals may be hazardous when used with this sprayer.
Congratulations!
You have just purchased a quality Chapin product.
Register Your Sprayer Online @ www.chapinmfg.com
Questions? Do Not Return To Store.
Call us @ 1-800-950-4458 or www.chapinmfg.com
¡Felicitaciones!
Usted acaba de adquirir un producto de calidad Chapin.
Registre su pulverizador en línea en www.chapinmfg.com
¿Preguntas? No regrese a la tienda;
llámenos al 1-800-950-4458 o visite www.chapinmfg.com
Félicitations!
Vous avez acheté un produit de qualité Chapin.
Enregistrez dès que possible votre pulvérisateur en ligne à l'adresse suivante:
www.chapinmfg.com
Questions ? Ne retournez pas au magasin.
Appelez-nous 1-800-950-4458 ou visitez le www.chapinmfg.com
Parts, Piezas, Pièces
6-2001
3-6006
Hose
Nozzle
Manguera
Boquilla
Tuyau
Buse
6-2000
Shut-off Handle
Mango de cierre
Poignée du robinet
6-7749
Extension wand
Vara de extensión
Rallonge
Note: Your particular sprayer may not include all parts pictured above.
Nota: Es posible que este pulverizador en particular no incluya todas las partes que se ilustran arriba.
Remarque : Votre pulvérisateur particulier pourrait ne pas inclure toutes les pièces illustrées plus haut.
Repair Parts Kit Gaskets and Seals (not included),
Juego de piezas de reparación, empaquetaduras y juntas (no incluido)
Kit de pièces de réparation, joints et garniture d'étanchéité (non inclus)
To prevent hose from blowing off, hose must cover both barbs and touch
flange (fig. 1B) before hose nut is tightened (fig. 1C).
1. Hose to Tank
1A
Sk-1154-1
Do: Place end of hose under
hot tap water for 1 minute.
This will soften the hose and
help insure the hose is pushed
all the way down to the flange.
2. Nozzle
2A
Nozzle
Shut-off
Handle
Attach nozzle to shut-off handle or extension wand.
3. Filter
The filter helps prevent clogging while spraying. It is located on the end
of the outlet tube inside your sprayer tank. To clean filter, remove the dis-
charge assembly from the tank (Fig. 3A). Make sure the filter is positioned
at the bottom of the tank as pictured.
4. Pre-Use Check
1) Do: Check tightness of hose nut to be sure hose is securely attached to the tank outlet.
2) Do: Inspect hose for deterioration, cracks, softness, or brittleness. If any of these conditions are found,
replace hose before using. Replace with original manufacturer's parts only.
3) Do: Remove pump (see Filling, Pressurizing and Spraying Instructions), inspect interior and exterior
of tank for signs of deterioration of body and bottom. Any sign of deterioration indicates possible tank
weakening and could result in explosive bursting under pressure. If any of these signs are found, discard
tank immediately and replace. Do not attempt to patch leaks, etc., as this could result in serious injury.
4) Do: Follow Filling, Pressurizing and Spraying Instructions, except use water only (Pump plunger 10-20
strokes and inspect for leaks).
5) Do: Direct shut-off away from you and open to make sure discharge is not clogged.
6) Do: If unit passes this test, release pressure (see Pressure Releasing Instructions), empty tank, and proceed
with Filling, Pressurizing and Spraying Instructions.
7) Do: Inspect all metal parts including the wand, nozzle and fittings for rust, corrosion and pitting. If any
of these conditions are found, replace affected part with original manufacturer's part before using.
5. Filling
1) Do: Turn pump handle counterclockwise and remove pump
2) Do: Prepare spray solution following all directions and safety warnings on chemical label.
6-1925
3) Do: Fill tank to no more than the proper gallon marker. Do NOT: overfill to accommodate pump.
4) Do: Check pump to make sure that no grass or dirt is stuck to barrel. Replace pump in tank and tighten securely.
016297 (A) R0918
WARNING
1B 1C
Flange
Do: Push hose until it Do: Slide nut down over
covers both barbs and threads. Turn nut clock-
touches the flange. wise as tight as possible.
Wand
Nozzle
Shut-off
Handle
3A
Filter
6. Pressurizing and Spraying
6A 6B 6C
Do: Turn handle clockwise Do: Pump until you Do: Push handle, down,
to tighten. Push handle feel resistance. turn 1/4 turn clockwise to
down, turn 1/4 turn coun- lock. Begin spraying. Re-
terclockwise to release. pump sprayer as required
to maintain spray force.
7. To Release Pressure
1) Do: With pump facing away, turn locked handle counterclockwise until air begins to escape.
Stop turning handle when you hear air escaping.
2) Do: Stay away from the sprayer until all air has escaped.
8. Care, Storage and Maintenance
1) Do: Rinse tank thoroughly with water only, empty, refill with water. Follow Filling, Pressurizing and Spraying
Instructions, except pump unit only 8-10 strokes. Be sure that the wand and nozzle are thoroughly rinsed with
water after each use.
2) Do: Open shut-off and allow water to run through discharge assembly.
3) Do: Release pressure (Follow Pressure Release Instructions), remove pump and empty sprayer.
4) Do: Store sprayer tank upside down, with pump removed, in a warm dry location.
5) Do: Periodically oil pump by dropping 10-12 drops of light oil down pump rod through opening in cover.
9. Troubleshooting
Tank pressurizes but does not spray.
-
WARNING: Release pressure in tank before troubleshooting.
Clean shut-off (Fig. 9A- 9D)
9A 9B 9C
Handle
Pull handle straight Insert notches from Remove plunger, diaphragm and spring. Wash
up. underside of handle into diaphragm with mild detergent. Reassemble:
plunger grooves and turn Hold shut-off upright as shown, place spring
counterclockwise. in hole, place diaphragm on top of spring.
Reassemble plunger and tighten.
9D
Tighten plunger clockwise until flush to top
Plunger flush
of shut-off body. Do not over-tighten or unit
with body
may not spray. Slide forks under plunger,
push handle down until it snaps into place.
Clean Nozzle Assembly (Fig. 9E) -Remove nozzle cap. Clean and re-assemble.
9E
Nozzle Cap
6D
Do: Turn end of
nozzle to adjust
spray pattern.
Plunger
Diaphragm
Spring