Chapin 22149XP Manual Del Usuario

WARNING!
Hazard: Improper use or failure to follow instructions can result in explosive failure causing
serious eye or other injury. For safe use of this product you must read and follow all instructions.
Do not leave a pressurized sprayer in the hot sun. Heat can cause pressure build-up. Do not store
or leave solution in tank after use. Always wear goggles, gloves, long sleeve shirt, long pants and full
foot protection when spraying. Never use any tool to remove pump if there is pressure in sprayer.
Never stand with face or body over top of tank when pumping or loosening pump to prevent eject-
ing pump assembly and/or solution from striking and injuring you. Never pressurize sprayer by any
means other than the original pump. Do not attempt to modify or repair this product except with
original manufacturer's parts. Never spray flammable materials or heat, pressure, or gas produc-
ing chemicals. Always read and follow manufacturer's instructions before use with this sprayer
as some chemicals may be hazardous when used with this sprayer.
WARNING: Handling the brass parts of this product will expose you to lead, a chemical known
to the State of California to cause birth defects and other reproductive harm. Wash hands after
handling.
Congratulations!
You have just purchased a quality Chapin product.
Register Your Sprayer Online @ www.chapinmfg.com
Questions? Do Not Return To Store.
Call us @ 1-800-950-4458 or www.chapinmfg.com
Felicitaciones!
¡
Usted acaba de adquirir un producto de calidad Chapin.
Registre su pulverizador en línea en www.chapinmfg.com
¿Preguntas? No regrese a la tienda;
llámenos al 1-800-950-4458 o visite www.chapinmfg.com
Félicitations!
Vous avez acheté un produit de qualité Chapin.
Enregistrez dès que possible votre pulvérisateur en ligne à l'adresse suivante:
www.chapinmfg.com
Questions ? Ne retournez pas au magasin.
Appelez-nous 1-800-950-4458 ou visitez le www.chapinmfg.com
Parts, Piezas, Pièces
6-5943 6-5797
Nozzle 1.0 GPM Nozzle .5GPM
6-6090
Tobera Tobera
Hose Black
Buse Buse
Manguera para trabajos pesados Negro
Tuyau pour service intense Noir
6-8136
6-8135
Valve Kit
Dripless Shut-off
Kit de la válvula
Cierre antigoteo
Ensemble de soupape
Arrêt anti-goutte
Note: Your particular sprayer may not include all parts pictured above.
Nota: Es posible que este pulverizador en particular no incluya todas las partes que se ilustran arriba.
Remarque : Votre pulvérisateur particulier pourrait ne pas inclure toutes les pièces illustrées plus haut.
Repair Parts Kit Gaskets and Seals (not included),
Juego de piezas de reparación, empaquetaduras y juntas (no incluido)
Kit de pièces de réparation, joints et garniture d'étanchéité (non inclus) 6-5387
1. Hose to Tank
1A
Outlet
Tube
Outlet Tube
Adapter
1C
Sk-1113-1
Discharge/ Assembly
• Make sure white outlet tube is attached to outlet tube adapter (Fig. 1A).
• Insert the outlet tube portion of the discharge assembly into the tank adapter (Fig. 1B).
• Proper placement of white outlet tube (Fig. 1C).
• Firmly insert the outlet tube adapter into the tank adapter (Fig. 1D) Lining up tab
with notches on the tank adapter.
• Firmly tighten the retaining nut to the tank adapter (Fig. 1E).
2. Nozzle
Attach nozzle to shut-off handle or extension wand.
Metal Rod
6-4607
Pressure Relief Valve
Válvula de descarga de presión
3. Pre-Use Check
Soupape de décompression
1) Do: Check tightness of hose nut to be sure hose is securely attached to the tank outlet.
2) Do: Inspect hose for deterioration, cracks, softness, or brittleness. If any of these conditions are found,
replace hose before using. Replace with original manufacturer's parts only.
301630-3
3) Do: Remove pump (see Filling, Pressurizing and Spraying Instructions), inspect interior and exterior of tank
Pump Assembly
Asamblea de la bomba
for signs of deterioration of body and bottom. Any sign of deterioration indicates possible tank weakening and
Assemblée de pompe
could result in explosive bursting under pressure. If any of these signs are found, discard tank immediately and
replace. Do not attempt to patch leaks, etc., as this could result in serious injury.
4) Do: Follow Filling, Pressurizing and Spraying Instructions, except use water only.
5) Do: Pump plunger 8-10 strokes and inspect for leaks.
6) Do: Direct shut-off away from you and open to make sure discharge is not clogged.
7) Do: If unit passes this test, release pressure (see Pressure Releasing Instructions), empty tank, and proceed with
Filling, Pressurizing and Spraying Instructions.
011534-4 (A) R0412
1B
Outlet
Tube
Discharge
Assembly
No Outlet Tube
1D 1E
Gap Adapter
Tab/
Retaining Nut -
Tank Notch Securely tightened.
Adapter
2A Valve Seat 2B
OR
Nozzle
Nozzle Adapter
2C
Brass Extension Nut
Metal Rod Brass Extension
Metal Rod
To attach nozzle to shut-off, unthread nozzle adapter and re-
2D
move valve seat from extension (2B). Unthread brass extension
nut and metal rod (2D). Assemble valve seat to shut-off then
assemble nozzle adapter as shown in figure (2A).
Note orientation of valve seat. It will leak if assembled wrong .
4. Filling
1) Do: Turn pump handle counterclockwise and remove pump
2) Do: Prepare spray solution following all directions and safety warnings on chemical label.
3) Do: Fill tank to no more than the proper gallon marker. Do NOT: over fill to accommodate pump.
4) Do: Check pump to make sure that no grass or dirt is stuck to barrel. Replace pump in tank and tighten
securely.
5. Pressurizing and Spraying
5A 5B
Do: Turn handle clockwise to Do: Pump until you
tighten. Push handle down, feel resistance.
turn 1/4 turn counterclock-
wise to release.
6. Lock Off
For safety lock-off feature (no-spraying), push trigger forward
and rotate locking mechanism into lock-off position as shown
in fig. 6A.
7. To Release Pressure
1) Your sprayer is equipped with a pressure relief/release valve
7A
(Fig. 7A). To release pressure lift and hold the cap until air
is completely exhausted, OR, turn the valve slowly counter
clockwise until you hear air escaping and wait air is completely
exhausted (Fig. 7B).
2) Do: Stay away from the sprayer until all air has escaped.
8. Wand Dock Clip
Choose the holder that fits your wand.
9. Care, Storage and Maintenance
1) Do: Rinse tank thoroughly with water only, empty, refill with water. Follow Filling, Pressurizing
and Spraying Instructions, except pump unit only 8-10 strokes.
2) Do: Open shut-off and allow water to run through discharge assembly.
3) Do: Release pressure (Follow Pressure Release Instructions), remove pump and empty sprayer.
4) Do: Store sprayer tank upside down, with pump removed, in a warm dry location.
5) Do: Periodically oil pump by dropping 10-12 drops of light oil down pump rod through
opening in cover.
P.O. Box 549 700 Ellicott St.
Batavia, NY 14021-0549 U.S.A.
1-800-950-4458 www.chapinmfg.com
5C
Do: Push handle, down, turn
1/4 turn clockwise to lock. Begin
spraying. Re-pump sprayer as
required to maintain spray force.
6A
Lock
Trigger
7B