DeWalt DWH050 Traducido De Las Instrucciones Originales página 25

Attach Dust Extraction System to
Dust Extractor (fi g. 1, 3, 4)
WARNING: Use only power tools
recommended by D WALT with this
E
attachment. For more information about
D WALT power tools compatible with this
E
attachment, please contact your local dealer,
refer to the addresses at the back of the
manual or visit www.dewalt.eu.
Push recommended dust extractor hose nozzle
(k) into connection point (c) until tight. For a more
secure connection use the AirLock connection
system.
NOTE: Ensure hose connection is secure.
AIRLOCK CONNECTOR SYSTEM - DWV9000
(SOLD SEPARATELY)
AirLock allows for a fast and secure connection
between the drilling dust extraction system and the
dust extractor.
1. Ensure the collar (l) on the AirLock connector
(m) is in the unlock position. Align notches (r)
on collar and AirLock connector as shown for
unlock and lock positions.
2. Push the AirLock connector (m) onto the
connection point (c).
3. Rotate the collar (l) to the locked position.
NOTE: The ball bearings (n) inside collar will
lock into slot (o) and secure the connection.
The drilling dust extraction system is now securely
connected to the dust extractor.
Attach Drilling Dust Extraction
System to Vertical or Horizontal
Surface (fi g. 1, 5, 8, 9)
The dust extraction system (d) has a suction system
that allows the unit to be fixed into place on a
vertical or horizontal surface.
1. With the correct drilling head (g, h) attached
and the drilling dust extraction system securely
connected to the dust extractor, turn the dust
extractor on as instructed in the dust extractor
instruction manual.
2. Depress and hold the quick release buttons
(e) and place the dust extraction system (d) on
surface to be drilled.
NOTE: The suction system will not hold the
unit in place on very rough or uneven surfaces.
Secure the dust extraction system in place
as shown in figure 9 if drilling on an uneven
horizontal surface.
3. Release the quick release buttons (e) and the
dust extraction system will be secured in place.
4. To make fine location adjustments, depress
the quick release buttons (e) and the seal will
release so the unit can be moved or removed
from the surface completely.
Remove Drilling Dust Extraction
System from Surface (fi g. 1, 5)
WARNING: DO NOT turn off the dust
extractor before removing the drilling
dust extraction system from the surface
as instructed. Turning off the dust
extractor before removing the drilling
dust extraction system will result in the
drilling dust extraction system falling
from the surface which could cause
injury
Depress the quick release buttons (e) on the dust
extraction system to remove it from the surface.
Attach Hole Cleaning Nozzles
(fi g. 1, 6, 7)
Hole cleaning is required to expose the full drilled
depth and when using certain types of chemical
fixing anchors to ensure maximum adhesion.
1. Select the correct hole cleaning nozzle to be
used:
• Hole cleaning nozzle (a): used for small holes
8 mm to 14 mm in diameter.
• Hole cleaning nozzle (b): used for holes
14 mm in diameter and above.
2. Remove/replace hole cleaning nozzle:
Grip the nozzle (a, b) firmly and pull it from the
connection point (j).
Push the nozzle into the connection point (j) until
it stops.
3. Push the dust extractor hose nozzle into the
connection point (c) until tight. For a more
secure connection the AirLock connection
system may be used.
NOTE: Ensure hose connection is secure.
AIRLOCK CONNECTOR SYSTEM - DWV9000
(SOLD SEPARATELY)
AirLock allows for a fast and secure connection
between the hole cleaning nozzle and the dust
extractor.
1. Ensure the collar (l) on the AirLock connector
(m) is in the unlock position. Align notches (r)
on collar and AirLock connector as shown for
unlock and lock positions.
EN G LI SH
23