Tabla de contenido
Publicidad
CONTENTS
ROLLER COASTER . . . . . . . . . . . . . . . . 4
Tips & Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . 27
FERRIS WHEEL . . . . . . . . . . . . . . . . . 28
Tips & Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . 41
Foreign Languages . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
IMPORTANT STUFF FOR PARENTS & KIDS
!
WARNING: CHOKING HAZARD - Small parts.
Not for Children under 3 years.
CAUTION: Keep hands, face, hair and clothing away from all
moving parts.
CAUTION: Be careful not to tip the model over. Model should be
placed on a flat and hard surface.
•
Share the K'NEX experience with your child and make building
with K'NEX a family fun adventure.
•
Take your time to enjoy the building process. Don't rush!
•
While you're building make sure you face your model in the same
direction as the pictures show in the instructions.
•
Be sure to install batteries into the motors before you start building
your motorized models.
•
Product and colors may vary.
Special Light-Up parts:
•
Inspect the light-up module and rods before each use. Do not use
if insulation is cut, frayed or torn.
•
Do not put anything but the light-up rods or K'NEX rods into the
sockets of the light module.
•
Keep all light-up rods and light module components dry. Do not
immerse in water.
•
Be sure to turn the light module switch OFF when finished.
•
Do not leave the light module on when not in use.
•
A slight humming noise is normal for the light module.
Test the Lights:
•
Insert 2 AAA (LR03) batteries into the light
module and test your lights before building.
•
Plug the metal ends (contacts) of the
light-up rods firmly into the light module.
•
Turn the light module switch to the
continuous ON and BLINK positions.
Lights not working?
•
Check to see if you have fresh batteries
inserted with the correct polarity.
•
Check to see if the metal ends of light-up rods are fully plugged
into the light module. (The ends with the metal tips must be
inserted all the way into the light module to make contact.)
•
Turn the light module switch to the continuous ON or BLINK positions.
•
If the lights are still not working, call or write to us using the
information on the back cover.
Caution: To Avoid Battery Leakage
•
Alkaline batteries are recommended.
•
Rechargeable batteries are not recommended.
•
Remove rechargeable batteries from toy
before charging; they must be charged only
under adult supervision.
•
Keep components free of dust; do not
immerse or use in water.
•
Non-rechargeable batteries must not be recharged.
Important Tips:
•
As with all small batteries, the batteries used
in this toy should be kept away from small
children, who still put things in their mouths.
If they are swallowed, promptly see a doctor
and have the doctor phone 202-625-3333
collect (US only). In Canada, have the doctor
call your Provincial Poison Control Center.
•
Do not mix old and new batteries or alkaline,
standard (carbon-zinc) or rechargeable
(nickel-cadmium) batteries. Only batteries of
INSTALLING BATTERIES
Install all batteries before you start building.
Sound Module:
•
Use a small Phillips head screwdriver to
open the Sound Module. Insert 3 fresh AAA
batteries (LR03), inside the compartment
with correct polarity (+/-).
•
Sound Module may not work properly in direct
sunlight.
•
Push the gray button on the side to activate
and deactivate sound.
2 Motors (green and black):
BLINK
OFF
•
Use a small Phillips head screwdriver to
ON
loosen the screw. Insert 2 fresh AA batteries
(LR6) into each motor compartment with the
There are 3 switch
positions on the
correct polarity (+/-).
Light-Up Module:
light module.
•
Use a small Phillips head screwdriver to
loosen the screw. Insert 2 fresh AAA (LR03)
into the light module compartment with the
correct polarity (+/-).
®
LyTec
is a registered trademark of Elam EL Industries Ltd.
FR
LyTec
ES
LyTec
BATTERY INFORMATION
®
est une marque déposée de Elam EL Industries Ltd.
®
es una marca registrada de Elam EL Industries Ltd.
•
Do not dispose of batteries in a fire; they
could leak or explode and cause injury.
•
Remove all batteries if the toy will not be
used for a long period of time.
•
Do not put rods smaller than 2 inches in
any openings of the motor; they will damage
the motor, and cannot be removed.
the same or equivalent type recommended
should be used.
•
Be sure to insert the batteries correctly
and always follow the toy and battery
manufacturers' instructions.
•
Insert batteries with correct polarity (+/-).
•
Always remove weak or dead batteries
from the product; do not short-circuit supply
terminals.
Sound Module
+
+
Motor
+
Light-Up Module
+
+
Publicidad
Tabla de contenido
